ASOCRET-BIS-16_Technical Data Sheet EN 4820.pdf
3 Pages
101 KB
Download
<h1>ASOCRET-BIS-16_Technical Data Sheet EN 4820.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASOCRET-BIS-1/6 </p> <p> </p> <p>Art.-No. 2 06437</p> <p>Mineral-based fine repair mortar for 1–6 mm voids</p> <p>1119 <br />SCHOMBURG GmbH & Co. KG <br />Aquafinstraße 2–8 <br />D-32760 Detmold</p> <p>20 <br />2 06437-2 <br />DIN EN 1504-3 <br />ASOCRET-BIS-1/6 <br />Concrete replacement for non-structural <br />repair to EN 1504-3: ZA.1a <br />Compressive strength <br />R2 <br />Chloride ion content <br />≤ 0.05 % <br />Adhesive bond <br />≥ 0.8 N/mm² <br />Restrained shrinkage/expansion <br />NPD <br />Resistance to temperature change, <br />part 1 <br />≥ 0.8 N/mm² <br />-2 <br />-0.5 <br />Capillary water absorption <br />≤ 0.5 kg × m × h <br />Carbonation resistance <br />passed <br />E-modulus <br />≥ 20 GPa <br />Reaction to fire <br />Class A1 <br />Durability NPD <br />NPD = „No Performance Determined“</p> <p>• Impermeable to water <br />• Water vapour permeable <br />• Frost fast and resistant to de-icing salts <br />• Very good working properties <br />• Application by trowel or spray <br />• Reduces CO2 penetration <br />• High resistance to carbonation <br />Areas of Application: <br />ASOCRET-BIS-1/6 is used for horizontal and vertical <br />areas as well as overhead areas as a non-sag fine <br />repair mortar for voids up to max. 6 mm. It is furthermore <br />suitable as a levelling compound for swimming pool <br />tanks and other tanks as well as for forming pool <br />edge details for the subsequent application of bonded <br />waterproof membranes or the installation of tiles. <br />Technical Data: <br />Basis: <br />factory blended dry mortar <br />Colour: cement grey <br />Grain size: <br />< 1.0 mm <br />Bulk density: <br />approx. 2.0 kg/dm3 <br />Pot life*: <br />approx. 60 minutes <br />Overcoat after: <br />min. 1 day</p> <p>Substrate/ <br />application temp: <br />min. +5 °C, max. +30 °C <br />Compressive strength: 24 hrs, approx. 11 N/mm² <br /> <br />7 days, approx. 30 N/mm² <br /> <br />28 days, approx. 40 N/mm² <br />Flexural strength: <br />24 hrs, approx. 2 N/mm² <br /> <br />7 days, approx. 7 N/mm² <br /> <br />28 days, approx. 8 N/mm² <br />Consumption: approx. 1.6 kg/m²/mm <br />thickness <br />Cleaning: <br />Thoroughly clean work tools <br /> <br />with water after use <br />Packaging: <br />25 kg bag <br />Storage: cool and dry, 12 months in the <br />original unopened packaging. <br />Use opened packaging <br />promptly. <br />*) At +23°C and 50% RH. Due to weather and site conditions, these <br />given figures may lengthen or shorten.</p> <p>Substrate preparation: <br />The substrate must be load-bearing, sound, have a good <br />key and be free from adhesion inhibiting materials such <br />as release agents, dust, laitance layers etc. Substrate <br />preparation e.g. grit-blasting, shot-blasting or high pressure <br />water jetting (500–2,000 bar) is required if no previous <br />concrete repair works have been carried out. <br />Adequately pre-wet the prepared substrate before <br />applying ASOCRET- BIS-1/6 at a time when the substrate <br />is matt-damp. <br />Minimum age of concrete substrate: 28 days <br />Tensile adhesion strength of the <br />concrete substrate: <br />min. 1.5 N/mm2 <br />Product preparation: <br />Dependent on the desired consistency, place approx. <br />5.0–5.25 l of clean water into a clean mixing bucket and <br />whilst mechanically stirring (drill approx. 300–700 rpm), <br />mix in as much dry powder until a lump free, smooth paste</p> <p>1/3</p> <p>48/20</p> <p>is achieved. The mixing time is approx. 2–3 minutes. <br />Allow to mature for 5 minutes then mix through once <br />again. When mixing larger quantities, use a forced <br />action mixer. Only mix as much material as can be used <br />within the pot life given above. <br />Application by hand: <br />Apply a scratch coat of ASOCRET-BIS-1/6 to the <br />prepared substrate and then lay to the desired thickness. <br />Striking off the mortar is determined by the application <br />involved using a suitable tool (lath, trowel etc) within the <br />pot life. After leaving for the appropriate length of time, <br />the surface can be finished using a felt-board or spongeboard. <br />Wet spray application: <br />The surface to be treated must be adequately wetted <br />until matt-damp. <br />Re-profiling with wet spray techniques is carried out <br />after mixing in a compulsory mixer with a suitable feed <br />pump using a 12 mm spray re-profiling gun or a <br />35/12 mm MAWO nozzle. For an even spray <br />pattern a high output construction compressor (min. <br />4 m3 air / 4–5 bar operating pressure) is a mandatory <br />requirement. <br />Without compulsory mixer: <br />Pump system: High Comp Power <br />Pump unit: <br />XP 120 <br />Water demand: approx. 160–180 l/hr <br />Nozzle: <br />MAWO nozzle 35/12 mm or 12 mm <br /> <br />re-profiling spray gun <br />Max. Pipe length: 30 m <br />Control nozzle displacement: 0.5 –1.0 m <br />PFT pump system: <br />Multi Mix compulsory mixer <br />Feed pump N2FU4000 / screw conveyor D8-1.5 <br />Reprofiling spray gun 12 mm <br />Max. Pipe length: 30 m <br />Control nozzle displacement: 0.5 –1.0 m</p> <p>Inotec pump system: <br />Inomix compulsory mixer ZM80 Jet Mix <br />Inobeam F21 light / screw conveyor D8-1.5 <br />Reprofiling spray gun 12 mm <br />Max. Pipe length: 30 m <br />Control nozzle displacement: 0.5–1.0 m <br />Material application: <br />Through the addition of air at the spray nozzle, the <br />mortar is sprayed in a circular manner in order to <br />achieve a clean spray pattern. The first pass of the <br />spray head is to fill holes and cavities and to even out <br />irregularities in the substrate. The second spray pass is <br />to achieve the required thickness and to finish with a <br />suitable smoothing tool. <br />Post-treatment: <br />Following the application of ASOCRET-BIS-1/6, it is <br />fundamentally necessary to protect the mortar surfaces <br />from drying out too quickly using suitable measures <br />Keep damp for at least 3–5 days using mist spray <br />nozzles or wet jute sacking as required also covered <br />with polythene sheets. The polythene sheets must be <br />fastened to the area treated, so that air exchange is <br />excluded. If the area in question is exposed to direct <br />sunlight, draughts, large temperature fluctuations and/or <br />low humidity then after care treatment must be intensified. <br />If it is intended to apply a mineral-based waterproof <br />slurry, then this can be used as an alternative after care <br />treatment after approx. 24 hours. <br />Important advice: <br />• Prior to carrying out concrete repair works the <br />actual condition should be inspected by an expert <br />or Structural Engineer. The inspection report is to be <br />given to the applicator prior to commencement of <br />repair work. <br />• Protect surfaces not being treated with <br />ASOCRET-BIS-1/6.</p> <p>2/3</p> <p>48/20</p> <p>• ASOCRET-BIS-1/6 mortar, which has already <br />stiffened should not be re-lifed by adding more water <br />or fresh mortar as there is a risk of inadequate strength <br />development. <br />Please adhere to the valid EC Safety Data Sheet. <br />GISCODE: ZP1</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case <br />of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the <br />user from a duty of care. Apply to a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />3/3</p> <p>SF/CoS/TM/KKa/Tet</p> <p>48/20</p>
