MONOFLEX-XL_Product_information_GB_2616.pdf
2 Pages
350 KB
Download
<h1>MONOFLEX-XL_Product_information_GB_2616.pdf</h1> <p>Product information <br />Adhesive</p> <p>MONOFLEX-XL <br />Flexible adhesive with high yield</p> <p>Technical Data: <br />Mixing ratio: <br /> </p> <p>9.2 to 11 l water : <br />25 kg MONOFLEX-XL</p> <p>Substrate/Application <br />temperature: </p> <p>+5°C to +25°C</p> <p>Open time*: </p> <p>> 30 mins</p> <p>Foot traffic/ready to <br />grout*: <br /> </p> <p>floor after approx. 24 hours <br />wall after approx. 12 hours</p> <p>Consumption: <br /> <br /> <br /> <br /> <br /> </p> <p>approx. 1.6 kg/ m² with a <br />6 mm notched trowel <br />approx. 2.1 kg/ m² with an <br />8 mm notched trowel <br />approx. 2.6 kg/ m² with a <br />10 mm notched trowel</p> <p>Full service conditions*: </p> <p>after approx. 7 days</p> <p>Reaction to fire: </p> <p>A1/A1fl</p> <p>Packaging: </p> <p>25 kg plastic bag</p> <p>C2 <br />Reaction to fire: <br />Bond strenght, as <br />Tensile adhesion after dry ageing: <br />Durability, as <br />Tensile adhesion strength after <br />water immersion: <br />Tensile adhesion strength after <br />heat ageing: <br />Tensile adhesion strength after <br />freeze/ thaw cycles: </p> <p>Class E <br />≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm²</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>TS/CoS/JD</p> <p>EN 12004 <br />MONOFLEX-XL <br />Cement-based adhesive with increased <br />performance for the installation of tiles <br />in interior and exterior areas</p> <p>26/16</p> <p>Areas of application: <br />• MONOFLEX-XL is a flexible adhesive for the thin-bed <br />installation of large format earthenware, vitrified and fully <br />vitrified tiles/slabs as well as other ceramic finishes, mosaics <br />and natural stone, which is neither sensitive to discolouration <br />nor is translucent. <br />• MONOFLEX-XL is suited for tiling to all substrates in <br />accordance with DIN 18157, part 1, e.g. concrete, aerated <br />concrete, plaster/render, cement-based and calcium sulphate <br />based heated and unheated (flow) screeds, masonry work, <br />moisture resistant plasterboard and gypsum fibre boards, <br />composite materials in expanded or extruded polystyrene with <br />a mortar coating and reinforcement layer embedded, etc. <br />• For tiling over mineral-based or dispersion-based <br />SCHOMBURG bonded waterproof membranes.</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />11 <br />2 04302</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>* These values relate to +20° C and 65% relative humidity.</p> <p>2 04302</p> <p>Product application: <br />Mix MONOFLEX-XL with clean water in a clean mixing bucket until <br />homogenous. Mix ratio: 9.2–11.00 litres water : 25 kg MONOFLEX-XL. <br />Allow to stand for approx. 3 minutes then remix. Do not prepare more <br />adhesive than can be used within the pot life. Spread the mixed adhesive <br />over the substrate surface and comb through with a notched trowel suitable <br />for the tile format. Install tiles within the adhesive open time.</p> <p>MONOFLEX-XL <br />Flexible adhesive with <br />high yield</p> <p>When installing large format tiles greater than 60 x 60 cm, we recommend <br />that MONOFLEX-XL is modified with UNIFLEX®-B. Modifying with <br />UNIFLEX®-B elastifier increases the deformability and adhesion strength of <br />MONOFLEX-XL. Dependent on the modification, deformability class S2 <br />can be achieved, which is particularly recommended for tiles larger than <br />60 x 60 cm. This considerably compensates for shear stresses, which can <br />lead to delamination in unfavourable exterior conditions. <br />UNIFLEX®-B is mixed with water for improved application and then mixed <br />with MONOFLEX-XL until homogenous.</p> <p>Properties: <br />• Extremely good slump resistance <br />with the best application <br />properties <br />• Long open time <br />• Easy application <br />• For large format tiles and <br />porcelain <br />• For heated screeds <br />• For interior and exterior use <br />• Tested in accordance with <br />DIN EN 12004 C2 TE <br />DIN EN 12002 S1</p> <p>Mixing ratio: highly deformable (relates to class C2 S2, <br />deformation > 5 mm):</p> <p>Application: <br />The substrate must be dry, load-bearing, adequately flat, free from <br />penetrating cracks and free from separating substances such as oil, paint, <br />laitance and loose parts. They must have a largely closed surface with a <br />surface strength and condition commensurate with their type. When <br />installing tiles, the substrate, substrate preparation and product application <br />must conform to DIN 18157, part 1. Prime porous substrates with <br />ASO®-Unigrund. <br />Heated floors are to be heated prior to installing tiles. The readiness of a <br />substrate to receive finishes is to be determined by the carbide (CM) <br />method and may not fall below the following values:</p> <p>io n</p> <p>ve</p> <p>l o w e m iss</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>2 Priming the substrate, e.g. with <br />ASO®-Unigrund</p> <p>3 Adding the adhesive to a clean mixing <br />bucket</p> <p>4 Mixing the adhesive</p> <p>5 Setting out the wall</p> <p>6 Combing out the adhesive bed</p> <p>7 Fixing the wall tiles</p> <p>8 Priming the substrate, e.g. with <br />ASO®-Unigrund</p> <p>9 Setting out the floor</p> <p>10 Combing out the adhesive bed</p> <p>12 Laying the floor tiles</p> <p>13 Finished area ready for use</p> <p>4.17 kg UNIFLEX-B : approx. 5.0 litres water : 25 kg MONOFLEX-XL</p> <p>•CT ≤ 2.0% (when installing large format tiles 1.5%) <br />•CA/CFA unheated ≤ 0.5%, heated ≤ 0.3%</p> <p>ry</p> <p>1 Cleaned, load-bearing substrate ready for <br />tiling</p> <p>11 Applying a contact layer with large <br />format tiles</p>
