ASO-R008 Technical Data Sheet EN 2217.pdf
2 Halaman
51,7 KB
Download
<h1>ASO-R008 Technical Data Sheet EN 2217.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASO-R008</p> <p>INDU-OilCleaner <br />Cleaner and maintenance agent for <br />industrial and oil contaminated floors <br />• aqueous combination of surface active substances <br />• not harmful to the environment <br />• phosphate free <br />• solvent free <br />• very economical <br />Areas of application: <br />ASO-R008 is suitable for use on small areas / spot <br />cleaning and finds use for cleaning stubborn oil stains <br />on backgrounds such as concrete, cemetitious screeds, <br />stone, ceramic, metal <br />• as a pre-clean prior to application of the special <br />primer ASODUR-SG2. <br />• in the steel and metalworking industry, workshops etc. <br />• for fundamentally cleaning and maintenance cleaning <br />of newly installed industrial floor coatings. <br />• for cleaning away rubber marks on existing industrial <br />floor coatings. <br />Technical Data: <br />Basis: aqueous combination of surface <br />active substances <br />pH value: <br />approx. 11 <br />Density: <br />approx. 1.02 g/cm3 at +23° C <br />Mixing ratio: <br />see below <br />Overcoatable with <br />ASODUR-SG2 *: immediately once wastewater has <br />been vacuumed away <br />(* for further advice refer to the Technical Data Sheet ASODUR-SG2)</p> <p>Art.-No. 2 05809</p> <p>Packaging: <br />1, 10 and 200 litres <br />Storage: frost-free. cool and dry, min. 5 years <br />when stored above +10° C to <br />+50° C in the original unopened <br />packaging. Use opened packagings <br />promplty. <br />Substrate: <br />• Concrete, cementitious screed, stone, ceramic, metal <br />• Newly installed industrial floor coatings <br />• Contaminated existing industrial floor surfaces <br />Preparation and application: <br />ASO-R008 is supplied as a concentrate and is diluted <br />with tap water dependent on the application. For <br />dilution refer to the table. <br />1. The diluted ASO-R008 is then filled into a hand <br />operated spray bottle or spray equipment and <br />sprayed on to the area to be cleaned. <br />2. Allow to act for a short while then scrub the sprayed <br />area with a scrubbing brush until a brown colouration <br />appears. <br />3. Leave the cleaned area to stand for 10 minutes. <br />4. Once this time has elapsed scrub once again <br />thoroughly. <br />5. Thoroughly rinse cleaned areas with clean water <br />(+60° C until +80° C). <br />6. Clean washed areas with a wet vacuum. <br />7. Assess cleaned areas for oil residues and if <br />necessary repeat the cleaning process.</p> <p>Dilution and material consumption as a guide: <br />Type of contamination:</p> <p>ASO-R008 <br />concentrate</p> <p>Water</p> <p>Application advice</p> <p>Cleaning oil spots</p> <p>1 part</p> <p>approx. 5 to 10 parts</p> <p>Manual use, spray bottle/brush</p> <p>Rubber marks</p> <p>1 part</p> <p>approx. 1 to 2 parts</p> <p>Carry out the initial clean with low dilution</p> <p>Fundamental clean</p> <p>1 part</p> <p>approx. 50 to 100 parts</p> <p>Maintenance clean</p> <p>1 part</p> <p>approx. 50 to 100 parts</p> <p>Use conventional brush cleaners for floor <br />areas</p> <p>1/2</p> <p>22/17</p> <p>Cleaning existing and contaminated <br />industrial floor coatings e.g. rubber marks: <br />ASO-R008 is supplied as a concentrate and is diluted <br />with tap water dependent on the application. For <br />dilution refer to the table on page 1. <br />Assess cleaned areas for residual contamination and if <br />necessary repeat the cleaning process / increase the <br />concentration. <br />Important advice: <br />• When cleaning large connected areas use <br />professional cleaners that operate with the <br />appropriate equipment. The advisory service of <br />SCHOMBURG is glad to be of further assistance in <br />these cases. <br />• Protect areas not to be treated from the effects of <br />ASO-R008. <br />• Applications that are not clearly explained in this <br />technical data sheet may only be carried out after <br />consultation with and written confirmation from the <br />Technical Services Department of SCHOMBURG. <br />• ASO-R008 is categorised in accordance with the <br />ordinance on hazardous substances. <br />Please observe a valid EU Health & Safety data sheet! <br />GISCODE: GF50</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>CJ/CoS/TM</p> <p>22/17</p>
