ASO-Unigrund-S Technical Data Sheet EN 0518.pdf
2 Halaman
174 KB
Download
<h1>ASO-Unigrund-S Technical Data Sheet EN 0518.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASO®-Unigrund-S </p> <p>Art.-No. 2 04201</p> <p>Rapid special adhesion promoting primer</p> <p>moisture resistant plasterboard, brickwork, aerated <br />concrete, lime-sand blocks, cement, calcium sulphate and <br />poured asphalt screeds, levelling compounds, natural <br />stone, steel and glass.</p> <p>v er</p> <p>y lo</p> <p>io n</p> <p>0799 <br />SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />18 <br />204990 <br />SANIFLEX-EU <br />Construction kit for producing waterproofing <br />for walls and floors in wet rooms</p> <p>w e m is</p> <p>s</p> <p>ASO-Unigrund-S is suitable for use in interior rooms <br />in accordance with the AgBB evaluation scheme <br />(Committee for Health-related Evaluation of Building <br />Products), the French VOC by-law and the Belgian <br />royal decree C-2014/24239. Very low emissions in <br />accordance with GEV-EMICODE, which as a rule leads <br />to positive evaluations within the framework of building <br />certification systems in accordance with DGNB, LEED, <br />BREEAM, HQE. Highest quality level 4, rows 2,3,8,9 <br />in accordance with the DGNB criterion “ENV 1.2 local <br />environmental impact“.</p> <p>0799-CPR-150 <br />ETA-17/0469 <br />ETAG 022-1 <br />Reaction to fire <br />Release of dangerous substances <br />Water vapour permeability <br /> with ASO-Unigrund-D <br /> with ASO-Unigrund-GE/K <br /> with ASO-Unigrund-S <br />Water impermeability to EN 13967 <br />Crack bridging ability <br />Tensile strength <br />Joint bridging ability <br />Watertightness at penetrations <br />Water resistance <br />Temperature resistance <br />Resistance to alkalis <br />Workability <br />Thickness </p> <p>E <br />see SDS <br />sd≈ 44m <br />sd≈ 9m <br />sd≈ 6.8m <br />waterproof <br />category 1: 0.4 mm <br />≥ 0.5 MPa <br />category 2: waterproof <br />category 2: waterproof <br />category 2: ≥ 0.5 MPa <br />category 2: Temperature resistant <br />category 2: Alkali resistant <br />applicable <br />at least 0.5 mm</p> <p>The product is a component of the SANIFLEX-EU system in <br />accordance with ETAG 022-part 1.</p> <p>• Ready to use. <br />• Solvent free. <br />• Rapid drying. <br />• For absorbent and non-absorbent substrates. <br />• For interior and exterior use. <br />• Low emissions.</p> <p>Technical Data: <br />Basis: <br />styrene butadiene <br />Colour: <br />pink – violet <br />Density: <br />approx. 1.33 g/cm3 <br />Packaging: <br />1 kg, 5 kg <br />Application/ <br />substrate temp: +5° C to +25° C <br />Temperature <br />resistance: <br />-20° C to +80° C</p> <p>Areas of application: <br />ASO-Unigrund-S is used as a primer to improve the <br />adhesion to absorbent and non-absorbent substrates prior <br />to the installation of ceramic finishes with cement-based <br />or dispersion-based SCHOMBURG thin or mid-bed <br />adhesives. ASO-Unigrund-S reduces the porosity of the <br />substrate and protects moisture sensitive substrates from <br />the water in cement-based adhesives. Suitable for use on <br />existing tiled finishes, hydraulically setting cement, cementlime renders and gypsum plasters, gypsum fibre boards,</p> <p>Ready for tiling: on non-absorbent substrates after <br />complete through drying <br />(approx. 1 hour at +15° C), on <br />absorbent substrates as soon as the <br />ASO-Unigrund-S surface is dry</p> <p>1/2</p> <p>05/18</p> <p>Product application: <br />Stir thoroughly before use. Evenly apply a thin coat of <br />ASO-Unigrund-S at right angles with a foam or lamb’s <br />wool roller. Use neat on non-absorbent substrates, on <br />absorbent substrates dilute 1:1 with water. On nonporous substrates further processes may only be carried <br />out once completely dry. Drying time approx. 1 hour. <br />On absorbent substrates tiles can be laid as soon as the <br />ASO-Unigrund-S is surface dry – approx. 5 minutes – and <br />touch-dry. The dry coating is transparent-pink and sand <br />grey. When using externally, protect ASO-Unigrund-S <br />with a bonded waterproofing system for use beneath tiled <br />finishes e.g. AQUAFIN-2K/M.</p> <p>Cleaning agents: water, remove dried on material <br />with ASO-R001 <br />Storage: Frost free, min. 12 months in the <br />original unopened container. Use <br />opened packaging promptly. <br />Consumption: approx. 50 to 100 g/m2 dependent <br />on the porosity of the substrate <br />(Note: Technical application trials <br />have shown that the consumption is <br />220 g/m2 when used on old tiled <br />finishes.) <br />Substrate preparation: <br />The substrate must be dry, load-bearing, adequately flat, <br />free from penetrating cracks and free from separating <br />substances such as oil, paint, laitance and loose <br />components. Abrade calcium sulphate screeds, vacuum <br />followed by priming with ASO-Unigrund-S. Substrates <br />must be dry, sound and free from contamination, dust and <br />separating agents. Remove weak or adhesion impairing <br />layers e.g. old adhesive, smoothing compounds or <br />paint residues by e.g. mechanically brushing, abrading, <br />scabbling or shot blasting.</p> <p>Advice: <br />• When applying ASO-Unigrund-S protect areas not to <br />be treated. <br />• Wash off splashes immediately with water. <br />GISCODE: D1</p> <p>The moisture content for ceramic tiling, when measured by <br />a carbide hygrometer (CM device), must not exceed: <br />• Cement-based screed 2.0 CM% for screeds on <br />insulation or separating layers in interior areas. <br />• Calcium sulphate screeds without underfloor <br />heating 0.5 CM%. <br />• Calcium sulphate screeds with underfloor <br />heating 0.3 CM%. <br />• Gypsum based plaster 1.0 CM%.</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>This technical data sheet does not consider local building codes or legal requirements. It shall be used as general reference for the product, based on our current knowledge and experience. <br />Legally binding is only the latest Data Sheet from one of our foreign subsidaries inside their sales territory. In any case of uncertainty please consult our technical department for further <br />information. <br />2/2</p> <p>WKD/CoS/TM</p> <p>05/18</p>
