ASODUR-EKF_205752_Englisch.pdf
6 Halaman
1,21 MB
Download
<h1>ASODUR-EKF_205752_Englisch.pdf</h1> <p>Technical data sheet <br />ASODUR®-EKF <br />Heavy-duty epoxy resin adhesive and joint mortar 1–20 mm</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>205752001</p> <p>6 kg, pail</p> <p>Medium grey</p> <p>85</p> <p>1</p> <p>205752002</p> <p>6 kg, pail</p> <p>titanium grey</p> <p>85</p> <p>1</p> <p>Areas of application <br />For laying and grouting tiles & boards <br />To establish coverings in chemically and mechanically stressed areas such as industrial kitchens, laboratories, swimming pools or areas in the <br />food and chemical industries <br />for heated and unheated substrates <br />For walls and floors <br />for interior and exterior use</p> <p>Product features <br />Epoxy resin adhesive and joint mortar <br />R2 T after DIN EN 12004 <br />RG in accordance with DIN EN 13888 <br />Joint widths From 1 to 20 mm <br />High chemical and mechanical resistance <br />Pot life of ca. 60 minutes <br />Can be walked on and jointed after ca. 16 hours</p> <p>Advantages <br />Highly resistant to acids and alkaline solutions <br />Resistant to mechanical influences such as power sweepers <br />Easy to wash</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/6</p> <p>15/09/2025</p> <p>Technical data sheet <br />ASODUR®-EKF <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Density, ready to use product (ISO 1183-1)</p> <p>2 component system <br />Filled epoxy resin <br />approx. 1.4 g/cm³</p> <p>Mixing <br />Mix ratio, component A <br />Mix ratio, component B</p> <p>100 weight proportion <br />6.2 weight proportion</p> <p>Application <br />Substrate temperature <br />Pot life <br />Foot traffic after <br />Application temperature</p> <p>approx. 10 - 30 °C <br />approx. 60 minutes <br />approx. 16 hours <br />approx. 10 - 30 °C</p> <p>Material rate <br />Material consumption rate according to the area of application</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Dry <br />2. Firm <br />3. Load-bearing <br />4. Free of cracks <br />5. Protected from moisture penetration from the rear <br />6. Free of adhesion inhibiting substances</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/6</p> <p>15/09/2025</p> <p>Technical data sheet <br />ASODUR®-EKF <br />Substrate quality class</p> <p>Preparing the surface <br />1. Heated screeds must be heated in accordance with recognised standards before installation of coverings. <br />2. A moisture measurement must be carried out using the CM method to assess whether it is ready to receive. The CM measurement must be <br />completed in accordance with the current working instructions FBH-AD from thetechnical information "Interface coordination with heated floor <br />constructions".</p> <p>Application <br />Mixing <br />1. Add the hardener to the resin. <br />2. The hardener must run completely out of the container. <br />3. Mix thoroughly with the mixer until a homogeneous consistency is achieved. <br />4. The hardener must be distributed evenly. <br />5. Decant the mixture and stir again before application.</p> <p>Adhesion of boards <br />1. Apply ASODUR®-EKF with a flat trowel. <br />2. Comb off evenly with a notched trowel. Choose a notched trowel that is suitable for the board size and the substrate. <br />3. Apply the boards by pushing them in and pressing them into place. <br />4. Apply in accordance with DIN 18157, part 3. <br />5. In exterior areas, application that is largely free of voids is required!</p> <p>Grouting of tiles and boards in screening process <br />1. Apply the mixed ASODUR®-EKF to the surface in portions. <br />2. Use an epoxy jointing board to insert directly into the clean and dry joints. <br />3. Fill the joints completely. <br />4. Strike off and remove the excess material in a diagonal direction to the grout line using the epoxy jointing board. <br />5. Use water and the hydro sponge board to emulsify material residues on the coating surface and the joints, and then clean with clear water. <br />Avoid material and water residues.</p> <p>Grouting with compressed air guns <br />1. Decant ASODUR®-EKF into a separate extraction container. <br />2. The cartridges are filled via a pressure plate. <br />3. A compressor with a capacity of at least 10 bar and a suction capacity of approx. 100 I/min. is required. <br />4. Use water and the hydro sponge board to emulsify material residues on the coating surface and the joints, and then clean with clear water. <br />Avoid material and water residues.</p> <p>Rework of damaged cement joints <br />1. The joint depth must be at least 3 mm. <br />2. Re-bond loose tiles with ASODUR®-EKF. <br />3. The joints must be dry, dust-free and free of adhesion-reducing substances. <br />4. Use water and the hydro sponge board to emulsify material residues on the coating surface and the joints, and then clean with clear water. <br />Avoid material and water residues.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/6</p> <p>15/09/2025</p> <p>Technical data sheet <br />ASODUR®-EKF <br />Physiological behaviour and protective measures <br />1. ASODUR®-EKF is physiologically flawless after hardening completely. <br />2. The hardener (B-component) is corrosive. It is therefore imperative to ensure that the skin does not come into contact with the hardener. We <br />recommend wearing protective gloves when working. <br />3. Clean any soiling with plenty of water and soap, preferably with the addition of 2% household vinegar. <br />4. If splashes get into the eyes, rinse immediately with plenty of water. Afterwards, rinse with an eye wash bottle filled with boric acid water – <br />available in medical supply shops – then consult an ophthalmologist immediately. Always observe the general protective regulations of the <br />Employer's Liability Insurance Association.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 10 - 25 °C for 12 months in the original canister. Promptly use opened container.</p> <p>Notes <br />Exposure to abrasive stresses during use may cause scratches in the surfaces which will be visible particularly in the case of dark colour <br />shades. This will not have a negative impact on functional capability. We recommend cleaning and treating the surfaces on a regular basis <br />with suitable cleaning and care agents in order to maintain the surface quality and appearance during use. <br />At low temperatures, we recommend heating the material in a water bath at approx. +50 °C before use and then letting it cool down to <br />room temperature. This restores the application properties. <br />Low object temperatures increase consumption. The material thus loses its good workability and the reaction times are prolonged. <br />Higher temperatures shorten the pot life. ASODUR®-EKF is classified in accordance with the German Ordinance on Hazardous Substances <br />(GefStoffV). <br />Slight colour differences, caused by different production batches and raw material fluctuations, are unavoidable. Neighbouring surface <br />sections should be coated using the same production batch (same batch no. on the delivered packaging). <br />Contaminated washing water with a maximum concentration of 5% resin mixture is subject to the EWL (European Waste List) code 20 01 30 <br />as municipal waste. <br />For detailed information on application, read and observe supplementary technical information no. 19 "Applying ASODUR® products".</p> <p>Relevant regulations <br />Planning, inspection of substrates and building site circumstances, laying, grouting and subsequent <br />care of the work must be done in accordance with the relevant DIN standards and recognised rules of <br />technology (e.g. the ZDB Data sheets of the Zentralverband Deutsches Baugewerbe e.V.(German <br />construction Association) in the latest version. <br />Observe applicable safety data sheet! <br />GISCODE: RE 90 <br />Explanations <br />Conformity / Declaration / Verification</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/6</p> <p>15/09/2025</p> <p>Technical data sheet <br />ASODUR®-EKF <br />Colours <br />titanium grey <br />Medium grey <br />Black</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />5/6</p> <p>15/09/2025</p> <p>Technical data sheet <br />ASODUR®-EKF <br />Chemical durability</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />6/6</p> <p>15/09/2025</p>
