ASODUR-GH-S_205798_Englisch.pdf
3 Halaman
790 KB
Download
<h1>ASODUR-GH-S_205798_Englisch.pdf</h1> <p>Technical data sheet <br />ASODUR®-GH-S <br />Rapid setting silicate casting resin</p> <p>Material number</p> <p>Contents</p> <p>Packaging</p> <p>Colour</p> <p>205798001</p> <p>600 ml</p> <p>Set</p> <p>light yellow</p> <p>Areas of application <br />As casting resin for “nailing” wide cracks with screed clamps <br />For non-positive sealing of cracks and joints <br />Suitable for heated substrates</p> <p>Product features <br />Two component <br />Resistant to alkaline solutions, diluted acids, salt solutions and many organic solvents <br />Full service conditions early <br />Low odour <br />Very low emission <br />Very good penetration characteristics</p> <p>Advantages <br />Easy and rapid mixing - without tools <br />Early loadability and workability <br />Including disposable gloves and screed clamps</p> <p>Existing test certificates <br />EMICODE licence</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/3</p> <p>30/06/2025</p> <p>Technical data sheet <br />ASODUR®-GH-S <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Consistency <br />Density (component A) <br />Density (component B) <br />Viscosity, ready to use product [value]</p> <p>2 component system <br />Mod. silicate resin <br />Liquid <br />approx. 1.12 g/cm³ <br />approx. 1.48 g/cm³ <br />approx. 1000 mPa*s</p> <p>Mixing <br />Mix ratio, component A <br />Mix ratio, component B <br />Mixing time</p> <p>1 weight proportion <br />1 weight proportion <br />approx. 15 - 20 seconds</p> <p>Application <br />Substrate temperature <br />Max. relative humidity <br />Pot life <br />Minimum reaction temperature <br />Mixing method, machines, tools <br />Consumption <br />Application temperature <br />Overcoat after <br />Hardening time / full resilience</p> <p>approx. 10 - 35 °C <br />80 % <br />approx. 10 minutes <br />min. 10 °C <br />Shake <br />Approx. 200 ml/m with 10 mm x 5 mm (joint depth x joint width) <br />approx. 10 - 35 °C <br />approx. 25 minutes <br />approx. 24 hours</p> <p>Processing equipment <br />Aids/tools <br />Filler</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Load-bearing <br />2. Dry <br />3. Firm <br />4. Grippy <br />5. Free of adhesion inhibiting substances</p> <p>Substrate quality class</p> <p>Crack preparation <br />1. Depending on their length, open the cracks or joints to 1/2 to 2/3 of the screed thickness using a cut-off wheel. <br />2. Cut approx. 10 cm long transverse slits at right angles to the crack one after the other every 30 cm. <br />3. Then clean the cut areas meticulously with an industrial vacuum cleaner and remove any dust. <br />4. Insert the screed clips provided into the transverse grooves.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/3</p> <p>30/06/2025</p> <p>Technical data sheet <br />ASODUR®-GH-S <br />Application <br />Mixing <br />1. The (ideal) material temperature during the mixing procedure is +15 °C. <br />2. Add the resin (component A) totally to the hardener (component B). <br />3. The resin must run out of the container completely. <br />4. Seal the container again and shake for around 15–20 sec. until the consistency is homogeneous and free of streaks. <br />5. After the mixing process, the sealing cap must be cut open to match the existing crack width.</p> <p>Crack filling <br />1. Apply the mixed casting resin to the cut joints until saturated. <br />2. Re-grouting may be necessary. <br />3. Use a spatula to remove excess material immediately. <br />4. After the gel phase has been reached, sprinkle the surface of the fresh casting resin completely with quartz sand (Ø 0.1–0.6 mm). <br />5. After hardening, vacuum off the unbound, loose quartz sand. <br />6. Fresh impurities can be removed with a suitable solvent, hardened material can only be removed mechanically.</p> <p>Cleaning tools <br />Clean tools immediately after use with suitable solvent.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 10 - 30 °C for 9 months in the original canister. Promptly use opened container.</p> <p>Notes <br />The indicated consumption quantities are calculated values without additions for textured surface roughness and absorbency, level <br />compensation and residual material in the container. We always recommend a calculated safety addition of 10% on top of the calculated <br />consumption quantities. <br />Higher temperatures shorten the pot life. Lower temperatures increase the application and hardening times. <br />Only once the screed has reached its permissible residual moisture content, i.e. is ready for laying, should the screed cracks and crack <br />control joints be closed. <br />Observe the technical data sheets of the products mentioned before starting work. <br />Applications that have not been clearly mentioned in this technical data sheet may only be carried out after the technical service department <br />of SCHOMBURG GmbH has been consulted, and after the said department has approved of such a course of action in writing. <br />For detailed information on application, read and observe supplementary technical information no. 19 "Applying ASODUR products".</p> <p>Relevant regulations <br />The recognised standards of construction engineering, the relevant guidelines and current regulations <br />must be observed. <br />Observe applicable safety data sheet! <br />GISCODE: PU40</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/3</p> <p>30/06/2025</p>
