AQUAFIN-CA Technical Data Sheet EN 1419.pdf
1 ページ
39.7キロバイト
Download
<h1>AQUAFIN-CA Technical Data Sheet EN 1419.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>AQUAFIN®-CA</p> <p>Art.-No. 2 07212</p> <p>Installation adhesive for waterstops</p> <p>• One component <br />• Solvent free <br />• Bonds to wet substrates <br />• Resistant to weathering, ageing and UV light <br />• Silicone-free <br />Areas of application: <br />For bonding fresh concrete waterproofing membranes <br />such as AQUAFIN-WM12 and expanding waterstops <br />to concrete substrates such as AQUAFIN-CJ4 and <br />AQUAFIN-CJ6. <br />Technical Data: <br />Basis: <br />polycarbon-ester <br />Consistency: <br />pasty <br />Colour: <br />grey <br />Density: <br />approx. 1.05 g/cm3 <br />Total deformation <br />tolerated: <br />max. 15 % <br />Skin formation: <br />immediately moisture proof <br />Smoothing time: <br />approx. 30 mins <br />Substrate/application <br />temp: <br />+5 °C to +35 °C <br />Temperature resistance: -25 °C to +95 °C <br />Resilience (recovery): > 80 % <br />Volume change: <br />up to approx. 6 % <br />Consumption: approx. 8–10 m/cartridge <br /> <br />dependent on the adhesive <br /> <br />thickness and width of the <br /> <br />adhesion zone <br />Packaging: <br />290 ml cartridge <br />Storage: <br />12 months when stored cool <br /> <br />and dry in the original <br /> <br />unopened packaging. Use <br /> <br />opened packaging promptly.</p> <p>Substrate preparation: <br />For fresh concrete waterproofing membranes such as <br />AQUAFIN-WM12: <br />Generously apply AQUAFIN-CA to the overlap area <br />of the substrate and press the next sheet into the fresh <br />adhesive. The concreting process can take place no <br />sooner than 8 hours after adhesion. <br />For swellable waterstops such as AQUAFIN-CJ3, <br />AQUAFIN-CJ4, AQUAFIN-CJ6: <br />The substrate must be load-bearing, largely flat, open <br />textured and be free from gravel pockets, cavities, gaping <br />cracks and ridges, dust as well as adhesion inhibiting <br />substances such as e.g. laitance layers. It may be <br />matt-damp but not wet. <br />Due to the very high adhesion, the installation adhesive <br />drags when pulled away. Therefore remove the cartridge <br />press with a jolt. Spread the installation adhesive <br />thoroughly over the prepared substrate and press the <br />appropriate expansive waterstop into the adhesive until <br />it oozes from the underside. The concreting process can <br />proceed 8 hours after bonding, at the earliest. <br />Advice: <br />• Protect areas not to be treated with the construction <br />adhesive from its effects. <br />• Please refer to the technical data sheets and <br />application advice for the water stops and fresh <br />concrete waterproofing membranes to be used. <br />GISCODE: RU3</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>1/1</p> <p>SE/KK</p> <p>14/19</p>
