BETOCRETE-CL170-P Technical Data Sheet EN 4219.pdf
2 ページ
97.3キロバイト
Download
<h1>BETOCRETE-CL170-P Technical Data Sheet EN 4219.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>BETOCRETE®-CL170-P</p> <p>Art.-No. 2 06443 <br />Crystalline waterproofing admixture with plasticizing effect</p> <p>Areas of application: <br />BETOCRETE-CL170-P can be applied to all concrete <br />where water penetration should be permanently <br />prevented.</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />17 <br />2 06443</p> <p>Chloride content <br />max. 0.10 M.-% <br />Alkali content <br />max. 10.5 M.-% <br />Corrosion behaviour <br />contains components only <br />from EN 934-1:2008, Annex A. 1 <br />Compressive strength <br />fulfilled <br />Reduced water demand <br />fulfilled <br />Air content <br />fulfilled <br />Dangerous substances <br />NPD</p> <p>These are for example: Cooling towers at power stations, <br />tanks and containers, retaining basins, swimming pools, <br />parking garages, parking lot levels, foundations, sandwich <br />units, waterproof concrete, sewer channels/manhole <br />access points, tunnels, concrete pipes and everywhere, <br />where watertightness is needed.</p> <p>NPD = „No Performance Determined“</p> <p>EN 934-2 <br />BETOCRETE-CL-170-P <br />Plasticizer for concrete <br />EN 934-2:T2</p> <p>Technical data: <br />Colour: <br />colourless, clear <br />Density (at +20°C): <br />1.19 g/cm3 <br />Application temp.: <br />+8°C to +40°C <br />Storage: frost free, not below +8°C, <br />protected from contamination; <br />12 months in the original <br />unopened container. Use <br />opened containers promptly. <br />Packaging: 1,100 kg containers <br />220 kg drums <br />25 kg kegs <br />Water pollution class: <br />1 (Self classification)</p> <p>BETOCRETE-CL170-P is a liquid admixture for designing a <br />water tight concrete with innovative 2 in 1 technology. <br />Initially it functions chemically and plasticizes the concrete. <br />In the next step, nano-scale crystals are formed in the <br />capillary system by special active catalysts, which become <br />active on contact with water. This forms a concrete which <br />is sustainable and permanently impermeable to water. <br />• Liquid <br />• Innovative 2 in 1 technology <br />• Crystallization of the capillaries <br />• Water reducing up to 10% <br />• Crack healing possible for penetrating cracks up to <br />0.4 mm and for map/pattern cracks up to 0.5 mm <br />• Improvement of the resistance to freeze/thaw <br />• Reduction in Chloride migration <br />• Minimization of maintenance and repair costs <br />• Time saving <br />• Simple and assured</p> <p>Concrete requirements: <br />Minimum cement content: CEM I <br />270 kg/m³ <br />CEM II <br />290 kg/m³ <br />CEM III /A 380 kg/m³ <br /> Pozzolanic cement with <br />pozzolan content >20%: <br />300 kg/m³ <br />Granulated slag: <br />max.100 kg/m³ <br /> Fly ash: <br />max. 80 kg/m³</p> <p>1/2</p> <p>42/19</p> <p>Advice: <br />• A storage temperature of > 30°C can lead to a brown <br />discoloration of BETOCRETE-CL170-P. This has no <br />influence on the product features. <br />• BETOCRETE-CL170-P has to be thoroughly mixed after <br />a longer storage period (> 2 months). <br />• Carry out preliminary trials in accordance with current <br />standards before using BETOCRETE-CL170-P or other <br />types of additives. <br />• Lignite fly ash is only suitable with restrictions. <br />• The use of CEM III/B&C cements is excluded. <br />• The prescribed crack width restrictions given by <br />the Planner/Engineer/Structural Engineer must be <br />respected in all circumstances. Differing interpretations <br />are to be proven with relevant design verification and <br />design suitability. <br />• Concrete with BETOCRETE-CL170-P must be produced, <br />installed and cured following current valid standards. <br />• In rare circumstances BETOCRETE-CL170-P may <br />influence the initial set of the concrete. As a system <br />compatible product, RUXOLITH-T5 (VZ) is available to <br />control the concrete.</p> <p>Product preparation: <br />Dosage: <br />The required dosage rate is 1.75–2.25% based on CEM <br />weight and is dependent, amongst other criteria, on the <br />concrete formula and the reactivity of the cement. The <br />dosage is to identify with a suitability trial. The following <br />dosage levels have stood the test of time: <br />w/c value < 0.4 <br />1.75% based on CEM <br />> 0.4–0.5 <br />1.85% based on CEM <br />> 0.5–0.55 <br />2.00% based on CEM <br />Do not exceed the maximum dosage level of 2.25 % <br />based on CEM weight. <br />For large cement quantities (≥ 400 kg/m3) a dosage of <br />7 kg/m3 is sufficient. <br />Dosage at concrete plants: <br />BETOCRETE-CL170-P can be added to the mix water or <br />added to the finished concrete mix. <br />Dosage in concrete trucks: <br />Place all the BETOCRETE-CL170-P into the mixing drum <br />and then mix well for 1 minute per m3 of drum contents but <br />for a minimum of 5 minutes and use quickly.</p> <p>Please observe a current valid EU safety data sheet!</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the German technical data sheet or the latest Data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>TB/SE/LiB</p> <p>42/19</p>
