ESCOSIL-2000-ST Technical Data Sheet EN 3318.pdf
3 ページ
173キロバイト
Download
<h1>ESCOSIL-2000-ST Technical Data Sheet EN 3318.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ESCOSIL®-2000-ST </p> <p>Art.-No. 2 05592</p> <p>Natural stone silicone</p> <p>Technical Data: <br />Basis: pure, unmodified, neutral curing <br />silicone sealant <br />Colours: white, jasmine, pergamon, silver <br />grey, grey, medium grey, beige, <br />caramel, jura beige, titanium grey, <br />graphite, brown, nut brown, black, <br />sand grey, bahama beige <br />Consistency: <br />paste <br />Specific gravity: <br />approx. 1.01 g/cm3 <br />Application temp: +5 °C to +35 °C <br />Skin formation: approx. 10 minutes at +23°C and <br />50% relative humidity <br />Curing after 1 day: approx. 2–3 mm at +23 °C <br />and 50% relative humidity <br />Shore-A-hardness: approx. 30 acc. to DIN 53505 <br />E module: approx. 0.48 – 0.55 N/mm2, <br />100% to DIN 53 504 <br />Permissible movement <br />accommodation: <br />25% *) <br />Tensile strength: approx. 1.4 N/mm2 <br />to DIN 53 504 <br />Elongation at break: approx. 400 % to DIN 53 504 <br />Temperature <br />resistance: <br />- 40 °C to +180 °C <br />Storage: dry and cool, 24 months in the <br />original unopened packaging. Use <br />opened packaging promptly. <br />Packaging: 310 ml, polyethylene cartridges <br />(310 ml x 12 tubes per box) <br />Cleaner: <br />ASO-R001 when in the fresh state</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />2014 <br />2 05592 <br />EN 15651-1, EN 15651-3, EN 15651-4 <br />ESCOSIL-2000-ST <br />11 component silicone sealant, neutral cure for use on facades, in sanitary areas, <br />for pedestrian paths <br />- Type F EXT-INT CC, S, PW INT <br />- Conditioning: method A <br />- Carrier material: anodised aluminium <br />- Pretreatment: Cleanprimer 1101 <br />Reaction to Fire <br />Release of hazardous materials and/or <br />chemicals harmful to the environment <br />Water- and air-tightness <br />a)Tensile behaviour under pre-stressing (+23°C/-20°C) <br />b)Stability <br />c)Loss of volume <br />d)Tensile strength <br />e)Tensile behaviour i.e. elongation under <br />pre-stressing after immersion in water <br />f)Tensile properties / secant modulus in cold climates (at -30 °C) <br />g)Tensile properties under pre-stressing in cold climates (at -30 °C) <br />h)Microbiological growth <br />Durability </p> <p>Class E <br />evaluated <br />passed (NF) <br />≤ 3 mm <br />≤ 10 % <br />passed (NF) <br />passed (NF) <br />≤ 0.9 MPa <br />passed (NF) <br />0 <br />passed (NF)</p> <p>• Elastic. <br />• Non slump. <br />• Smooth paste consistency. <br />• Oxime-interlacing. <br />• Contains fungicide. <br />• For interiors and exteriors. <br />• For walls and floors. <br />• Weather-, UV- and ageing-resistant. <br />• Watertight. <br />• With good chemical resistance. <br />• MEKO-free <br />Areas of application: <br />For the discolouration-free elastic jointing of natural stone <br />finishes (e.g. marble, granite, gneiss, sandstone etc.). No <br />risk of migration of plasticizers or other components that <br />can lead to picture framing. As a seal to wash basins, <br />bath tubs, shower trays, door and window frames and for <br />sealing movement and connecting joints.</p> <p>*) For interior floor application, a total deformation of 12.5% is permitted.</p> <p>Substrate preparation: <br />The areas of contact must be dry (concrete < 4 % <br />moisture), clean, dust free as well as free from constituents <br />that work as separating agents (e.g. oil, grease, paint <br />residues, sealers, cement slurries etc.). With sandstone <br />thoroughly brush clean the joint edges. Also during the</p> <p>1/3</p> <p>33/18</p> <p>Priming table:</p> <p>curing of ESCOSIL-2000-ST no moisture should be <br />allowed to penetrate including from the edges or the <br />bottom of the joints. <br />• For improving the bond to natural stone and when using <br />with metal such as cast iron, aluminium, galvanised <br />metal etc., the joints edges should be primed with <br />AG70. <br />• When applying to natural stone in wet areas pre-treat <br />with AG70. <br />• When using with sandstone, priming with a suitable <br />primer, such as OTTO-CHEMIE Primer 1102, is strictly <br />necessary. <br />• With painted and plastic surfaces carry out a site trial if <br />necessary. <br />• When using the primer AG70 there is a risk of spot <br />formation. Do not spray! Oil, tar and bitumen containing <br />backing strips are not suitable nor are natural rubber, <br />chloroprene or EPDM based materials. <br />• With rough, porous mineral-based substrates e.g. <br />concrete, aerated concrete, Eternit, render and <br />brickwork, prime the joint edges with a suitable primer, <br />such as OTTO-CHEMIE Primer 1225. <br />Product application: <br />Filling of the joint with ESCOSIL-2000 may be carried <br />out once the primer has dried. The general jointing <br />technology regulations must be followed. The surface <br />of the applied sealant can be subsequently smoothed, <br />i.e. before it has formed a skin, with a suitable tool. Due <br />to the sensitivity of natural stone it is recommended that <br />a special smoothing material, such as OTTO-CHEMIE <br />Marmor-Silicon-Glättmittel, is used. <br />When using conventional smoothing materials such as <br />washing-up liquid, spots may be left on the surface.</p> <p>Substrates</p> <p>ESCOSIL-2000 <br />Natural stone silicone</p> <p>Acrylic (bath tubs)</p> <p>AG70</p> <p>Aluminium untreated</p> <p>–</p> <p>Aluminium, anodised</p> <p>–</p> <p>Concrete</p> <p>AG70 / –</p> <p>Lead</p> <p>–</p> <p>Chrome</p> <p>AG70</p> <p>Iron, abraded</p> <p>–</p> <p>Stainless steel, rust free</p> <p>AG70 / –</p> <p>Tiles, glazed</p> <p>–</p> <p>Tiles, unglazed</p> <p>–</p> <p>Glass</p> <p>–</p> <p>Wood, glazed</p> <p>–</p> <p>Wood, varnished</p> <p>–</p> <p>Synthetic stone</p> <p>AG70 / –</p> <p>Copper</p> <p>–</p> <p>Plastic (profiles)</p> <p>–</p> <p>Melamine resin</p> <p>AG70</p> <p>Brass</p> <p>–</p> <p>Natural stone</p> <p>AG70* / –</p> <p>Polyester</p> <p>–</p> <p>PVC</p> <p>AG70</p> <p>Soft PVC (membranes)</p> <p>×</p> <p>Thinplate</p> <p>AG70</p> <p>Zinc</p> <p>AG70</p> <p>* strictly in wet areas <br />– = not required</p> <p>2/3</p> <p>33/18</p> <p>Advice: <br />• Protect areas, which are not to be treated from the <br />effects of ESCOSIL-2000-ST. <br />• Avoid skin contamination and remove with soap and <br />water as necessary. <br />• Avoid contact with eyes or mucous membranes with the <br />uncured silicone sealant ESCOSIL-2000-ST. <br />• Thoroughly rinse eyes with plenty of water and seek <br />medical attention. <br />• Avoid prolonged and repeated skin contact. <br />• Contains a blend of butoxime-silanes and butoxime. <br />May cause allergic reactions. This product should not <br />be repeatedly inhaled over long periods otherwise <br />damage to health cannot be excluded.</p> <p>• Strictly adhere to all safety measures for handling <br />solvent-based lacquers and solvents when using primer <br />AG70. <br />• AG70 <br />For an improved adhesion of silicone systems to metal, <br />concrete slabs and to natural stone. In combination with <br />metals such as e.g. iron which corrode on contact with <br />acetic acid use ESCOSIL-2000-ST or <br />ESCOSIL-2000-UW. In combination with concrete <br />blocks and natural stone use ESCOSIL-2000-ST. <br />• The current IVD data sheets are to be observed. <br />Please observe a current EU safety data sheet.</p> <p>Consumption table: <br />Joint dimensions and consumption (approx.) in m per 310 ml cartridge <br />Joint width in mm <br />5</p> <p>7</p> <p>10</p> <p>12</p> <p>15</p> <p>20</p> <p>25</p> <p>Joint depth in mm <br />5.0</p> <p>12.0 m</p> <p>7.0 <br />10.0</p> <p>8.0 m</p> <p>6.0 m</p> <p>6.0 m</p> <p>4.0 m</p> <p>3.0 m</p> <p>3.0 m</p> <p>2.5 m</p> <p>2.0 m</p> <p>1.5 m</p> <p>2.1 m</p> <p>1.7 m</p> <p>1.2 m</p> <p>1.0 m</p> <p>1.3 m</p> <p>1.0 m</p> <p>0.8 m</p> <p>12.0 <br />15.0</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case <br />of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the <br />user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />3/3</p> <p>WKD/TET/TM</p> <p>33/18</p>
