ASO-Joint-Tape-2000-Cross-Piece ASO-Joint-Tape-2000-T-Piece ASO-Joint-Sleeve Technical Data Sheet EN 0518.pdf
4 Halaman
125 KB
Download
<h1>ASO-Joint-Tape-2000-Cross-Piece ASO-Joint-Tape-2000-T-Piece ASO-Joint-Sleeve Technical Data Sheet EN 0518.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASO®-Joint-Tape-2000-Cross-Piece Art.-No 2 05940 <br />ASO®-Joint-Tape-2000-T-Piece <br />Art.-No 2 05941 <br />ASO®-Joint-Sleeve <br />Art.-No 2 05937 (Wall)</p> <p> <br />Art.-No 2 05937 (Floor) <br />Special pre-formed joint tapes for highly <br />demanding situations and heavy duty exposure <br />ASO-Joint-Sleeve-Floor is used for waterproofing flange <br />constructions, floor drains, thin flanges made from <br />stainless steel, brass, PVC-U etc., and large diameter pipe <br />penetrations in e.g. swimming pools, wet rooms. Also for <br />use with penetrations without flanges in areas in contact <br />with the ground exposed to ground moisture / water not <br />under pressure. The pre-formed pieces are installed into <br />the waterproof coating e.g. SANIFLEX, AQUAFIN-RS300, <br />AQUAFIN-2K, AQUAFIN-2K/M, AQUAFIN-1K-PREMIUM, <br />ASOFLEX-AKB, ADF-Balkonfolie and SANIFIN. The preformed pieces are easily installed and form an integral <br />bond with the named waterproofing system. The preformed pieces are suitable for wet duty exposure classes <br />A, B and C in accordance with technical test criteria and <br />for wet duty classifications A0, B0 in accordance with <br />the ZDB data sheet ‘bonded waterproof membranes’ in <br />interior and exterior areas. We recommend its use in wet <br />duty classification areas A0, B0, A, B, C as well as in <br />bathrooms, kitchens, in living accommodation, private and <br />public sanitary facilities, balconies and terraces, swimming <br />pools (pool shell and pool surround), underground car <br />parks, in areas in direct ground contact as well as in <br />structural movement joints.</p> <p>0799 <br />SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />18 <br />204990 <br />SANIFLEX-EU <br />Construction kit for producing waterproofing <br />for walls and floors in wet rooms <br />0799-CPR-150 <br />ETA-17/0469 <br />ETAG 022-1 <br />Reaction to fire <br />Release of dangerous substances <br />Water vapour permeability <br /> with ASO-Unigrund-D <br /> with ASO-Unigrund-GE/K <br /> with ASO-Unigrund-S <br />Water impermeability to EN 13967 <br />Crack bridging ability <br />Tensile strength <br />Joint bridging ability <br />Watertightness at penetrations <br />Water resistance <br />Temperature resistance <br />Resistance to alkalis <br />Workability <br />Thickness </p> <p>E <br />see SDS <br />sd≈ 44m <br />sd≈ 9m <br />sd≈ 6.8m <br />waterproof <br />category 1: 0.4 mm <br />≥ 0.5 MPa <br />category 2: waterproof <br />category 2: waterproof <br />category 2: ≥ 0.5 MPa <br />category 2: Temperature resistant <br />category 2: Alkali resistant <br />applicable <br />at least 0.5 mm</p> <p>• Composite material <br />• Particularly elastic and tear resistant <br />• Impermeable to water <br />• Water vapour permeable <br />• Thin build-up <br />• Guarantees the quick drying of adhesives and <br />waterproof membranes, which contain water <br />• Highly resistant to aggressive media</p> <p>The product is a component of the SANIFLEX construction <br />kit in accordance with ETAG 022-Teil 1. <br />Technical Data: <br />Basis: composite material <br />fleece-membrane-fleece <br />Colour: white with SCHOMBURG <br />lettering <br />Weight: <br />approx. 280 g/m² <br />Thickness: <br />approx. 0.51 mm ± 0.1 mm</p> <p>Areas of application: <br />The ASO-Joint-Tape-2000-Cross-Pieces and <br />ASO-Joint-Tape-2000-T-Pieces are for forming water <br />impermeable crossover details with loop formation <br />for movement joints and connecting joints. <br />ASO-Joint-Sleeve-Wall is used for waterproofing <br />pipe penetrations e.g. shower and bath tub fittings.</p> <p>1/4</p> <p>05/18</p> <p>Substrate preparation: <br />All usual substrates, which are correctly prepared <br />and suitable for use with the installation of waterproof <br />membranes or tiled finishes. Fine, non-penetrative cracks <br />on the surface of < 0.1 mm are acceptable.</p> <p>Testing: C <br /> omponent of the SANIFIN/ EU waterproof <br />system. Fulfills the requirements of the “test <br />principles for the granting of a general technical <br />test certificate for waterproofing materials in <br />combination with tiled finishes, part 2 sheet <br />form bonded waterproof membranes” for the <br />procurement of an abP. MPA Braunschweig test <br />certificate No. P-5078/818/08/MPA BS <br />Bursting pressure: <br />UV resistance to <br />DIN EN ISO 4892-2: <br />Resistance to <br />water pressure: <br />Temperature resistance, <br />min/max.: </p> <p>Product application: <br />Joint waterproofing, wall and floor junctions and <br />bay defining movement joints: <br />Using the waterproof membrane, bond <br />ASO-Joint-Tape-2000-S or ASO-Joint-Tape-2000-S <br />internal/external corners for use in corners, at the transition <br />between wall and floor as well as interface joints to the <br />prepared area without voids or folds. <br />Where structural movement joints/movement joints <br />cross over, ASOJoint-Tape-2000-T-Pieces or <br />ASO-Joint-Tape-2000-Cross-Pieces are available, which <br />permit them to be laid in a looped formation at cross over <br />points. Butt joints must be overlapped by 5 to 10 cm. <br />Ensure that a sealed connection to the surrounding <br />waterproof membrane is produced. <br />1. Coat both sides of the joint to be bridged with the <br />waterproof membrane to a width of at least 2 cm wider <br />than the waterproof tape, e.g. with a 4 – 6 mm notched <br />trowel. <br />2. Then thoroughly work the waterproof tape, without <br />voids or folds, into the waterproof membrane using <br />a steel trowel or pressure roller. Ensure that, as far <br />as possible, a full bed and wetting out is achieved. <br />Bonding must be performed in such as way as to <br />exclude the migration of water behind the waterproof <br />tape. <br />3. The waterproof tape is to be worked into movement <br />joints as a loop. Overlap butt joints within waterproof <br />tape sections or at interfaces with all waterproof tape <br />pre-formed pieces and corners by a minimum of 5 to <br />10 cm and bond with the waterproof membrane, <br />without voids or folds. Overcoat with the chosen <br />waterproof membrane.</p> <p>>1.5 bar <br />minimum 500 hrs <br />min. 1.5 bar <br />-22 °C to +90 °C</p> <p>Chemical resistance after 7 days storage at +22° C with <br />the following chemicals: <br /> Hydrochloric acid 3%, sulphuric acid 35%, <br />Citric acid 100 g/l, Lactic acid 5%, <br />potassium hydroxide 20%, <br />Sodium hydroxide 0.3 g/l, <br />Salt water 20 g/l (sea salt) <br />Packaging: <br />ASO-Joint-Tape-2000-Cross-Piece: <br />width 20 cm, 10 pieces per box <br />ASO-Joint-Tape-2000-T-Piece: <br />width 20 cm, 10 pieces per box <br />ASO-Joint-Sleeve-Wall: <br />12 x12 cm, packed 50 pieces per box <br />ASO-Joint-Sleeve-Floor: <br />45 x 45 cm, packed 25 pieces per box <br />Storage: 24 months when stored cool <br />and dry protected from sunlight <br />and weather influences</p> <p>2/4</p> <p>05/18</p> <p>Waterproofing structural movement joints <br />(safety joint): <br />Work ASO-Joint-Tape-2000-S in to the joint as a loop, <br />bond with a suitable waterproof membrane and bed <br />into the waterproofing layer without voids or folds as <br />described above. At cross over points insert <br />ASO-Joint-Tape-2000-T-Pieces as well as <br />ASO-Joint-Tape-2000-Cross-Pieces. Where there <br />is water under pressure, additionally insert <br />ASO-SR and bond a further section of <br />ASO-Joint-Tape-2000-S using the appropriate <br />waterproofing material and overcoat. <br />Waterproofing pipe penetrations and floor drains: <br />Wall area in wet duty exposure classes A0, A: <br />(wall areas exposed to mains or cleaning water <br />moderately or frequently and floor areas with light duty <br />exposure such as e.g. walls and floors in usual domestic <br />use without floor drainage with bath tubs or shower trays. <br />Furthermore for walls in commercial showers and walls <br />with splash contact in usual domestic bathrooms with <br />a floor drain). For waterproofing pipe penetrations in <br />wall areas, use either ASO-Joint-Sleeve-Wall or <br />ASO-Joint-Sleeve-Floor dependent on the diameter. The <br />diameter of the hole in the waterproof gasket must be <br />considerably smaller than the diameter of the pipe, so <br />that the waterproof gasket applies contact pressure to the <br />pipe due to its “memory”. As a point of reference, the hole <br />diameter can be estimated as approx. 50% of the pipe <br />diameter, with smaller pipes less and with larger pipes, <br />more. <br />1. Roughen the pipe penetration, clean and degrease. <br />2. Apply the waterproof membrane to the substrate and <br />pipe penetration. <br />3. Then, lightly stretching, push the hole in the <br />ASO-Joint-Sleeve-Wall over the pipe, press firmly in <br />place and cover with the waterproof membrane so that <br />a watertight bond is produced with the other areas of <br />the surrounding waterproof membrane.</p> <p>Floor and wall areas in wet duty exposure classes <br />A, A0, B0: <br />(Floor areas exposed to mains or cleaning water <br />moderately or frequently, buildings externally exposed to <br />water not under pressure e.g. bathrooms with floor drains, <br />balconies and terraces, floors in commercial showers, <br />swimming pool surrounds.) <br />1. L ay the ASO-Joint-Sleeve-Floor over the flange in the <br />floor drain, mark the size of the flange and cut the <br />required opening. <br />2. Roughen the thin flange, clean and degrease. <br />3. U <br /> sing a 4 – 6 mm notched trowel, apply the <br />waterproofing material appropriate for the wet duty <br />exposure class to the thin flange and the area of <br />overlap. <br />4. W <br /> hilst the material is still wet, press in the <br />ASO-Joint-Sleeve-Floor, bedding in without voids or <br />folds, so that a watertight bond is achieved with the <br />surrounding waterproof membrane. <br />Floor and wall areas in wet duty exposure classes <br />B and C: <br />(wall and floor areas in swimming pools in interior and <br />exterior areas with water under pressure from the inside. <br />Furthermore wall and floor areas with heavy duty water <br />exposure and limited chemical exposure such as e.g. <br />commercial kitchens). <br />1. L ay the ASO-Joint-Sleeve-Floor over the flange in the <br />floor drain, mark the size of the flange and cut the <br />required opening. <br />2. R oughen the thin flange, clean and degrease. <br />3. W <br /> ith a clean cloth, thinly wipe the stainless steel, brass <br />or PVC-U thin flange with the adhesion promoter <br />INDU-Primer-N. Allow to dry for 30 minutes up to 4 hrs <br />maximum, then proceed with the next steps. <br />4. W <br /> ith a 4 – 6 mm notched trowel, apply <br />ASOFLEX-AKB-Wall to the thin flange and to the <br />overlap area prepared with the DENSARE system.</p> <p>3/4</p> <p>05/18</p> <p>Whilst the material is still wet, press in the <br />ASO-Joint-Sleeve, bedding in without voids or folds, <br />so that a watertight bond is achieved with the <br />surrounding waterproof membrane. <br />5. Then broadcast ASOFLEX-AKB-Wall with dry <br />0.2 – 0.7 mm quartz sand, so that following coatings <br />achieve an adequate bond. <br />Once the waterproof membrane has cured, install tiles <br />using the thin-bed method. <br />Advice: <br />• Joints secured with ASO-Joint-Tape-2000-S or <br />appropriate pre-formed pieces must be adequately <br />protected from mechanical damage. <br />• ASO-Joint-Tape-2000-S or appropriate pre-formed <br />pieces may not be fixed or coated with solvent based <br />products. <br />• Wall/floor junctions in areas in the ground as well as <br />structural movement joints must be carried out with <br />ASO-Joint-Tape-2000-S. <br />• Follow recognised building technology regulations. <br />• Heed the relevant current regulations. <br />For Germany e.g.: <br />DIN 18157 <br />The BEB information sheets distributed by the <br />Bundesverband Estrich un Belag e.V. <br />The ZDB information sheets, distributed by the <br />professional association of the German Tile Industry: <br /> [*1] „Bonded waterproof membranes”“ <br /> [*3] „Movement joints in tiled wall and floor finishes” <br /> [*5] „Ceramic tiles, natural stone tiles and <br />cementbound tiles on cement-based floor <br />constructions on insulation” <br /> [*6] „Ceramic tiles, natural stone tiles and cementbound tiles on heated cement-based floor <br />constructions”</p> <p>This technical data sheet does not consider local building codes or legal requirements. It shall be used as general reference for the product, based on our current knowledge and experience. <br />Legally binding is only the latest Data Sheet from one of our foreign subsidaries inside their sales territory. In any case of uncertainty please consult our technical department for further <br />information. <br />4/4</p> <p>WKD/CoS/TM 05/18</p>
