ASOCRET-BIS-16_GB_TM_0617.pdf
3 Halaman
458 KB
Download
<h1>ASOCRET-BIS-16_GB_TM_0617.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASOCRET-BIS-1/6 (ASOCRET-FS/INDUCRET-BIS-1/6) </p> <p>Art.-No. 2 06437</p> <p>Mineral-based fine repair mortar for 1-6 mm voids</p> <p>1119 <br />SCHOMBURG GmbH & Co. KG <br />Aquafinstraße 2–8 <br />D-32760 Detmold</p> <p>16 <br />2 06437 <br />DIN EN 1504-3 <br />ASOCRET-BIS-1/6 <br />Concrete replacement for non-structural <br />repair to EN 1504:3:ZA:1a <br />Compressive strength <br />R2 <br />Chloride ion content <br />≤ 0.05 % <br />Adhesive bond <br />≥ 0.8 N/mm² <br />Restrained shrinkage/expansion <br />NPD <br />Resistance to temperature change, <br />part 1 <br />≥ 0.8 N/mm² <br />Capillary water absorption <br />≤ 0.5 kg × m × h <br />Carbonation resistance <br />passed <br />E-modulus <br />≥ 20 GPa <br />Reaction to fire <br />Class A1 <br />Durability NPD <br />-2</p> <p>-0.5</p> <p>NPD = „No Performance Determined“</p> <p>• Impermeable to water <br />• Water vapour permeable <br />• Frost fast and resistant to de-icing salts <br />• Very good working properties <br />• Application by trowel or spray <br />• Reduces CO2 penetration <br />• High resistance to carbonation <br />Areas of Application: <br />ASOCRET-BIS-1/6 is used for horizontal and vertical <br />areas as well as overhead areas as a non-sag fine <br />repair mortar for voids up to max. 6 mm. It is furthermore <br />suitable as a levelling compound for swimming pool <br />tanks and other tanks as well as for forming pool <br />edge details for the subsequent application of bonded <br />waterproof membranes or the installation of tiles. <br />Technical Data: <br />Basis: <br />factory blended dry mortar <br />Colour: cement grey <br />Grain size: <br />up to 0.5 mm <br />Pot life*: <br />approx. 60 minutes <br />Overcoat after: <br />min. 1 day</p> <p>Substrate/ <br />application temp: <br />min. +5 °C, max. +30 °C <br />Compressive strength: 24 hrs, approx. 11 N/mm² <br /> <br />7 days, approx. 30 N/mm² <br /> <br />28 days, approx. 40 N/mm² <br />Flexural strength: <br />24 hrs, approx. 2 N/mm² <br /> <br />7 days, approx. 7 N/mm² <br /> <br />28 days, approx. 8 N/mm² <br />Consumption: approx. 1.6 kg/m²/mm <br />thickness <br />Cleaning: <br />Thoroughly clean work tools <br /> <br />with water after use <br />Packaging: <br />25 kg bag <br />Storage: cool and dry, 12 months in the <br />original unopened packaging. <br />Use opened packaging <br />promptly. <br />*) At +23°C and 50% RH. Due to weather and site conditions, these <br />given figures may lengthen or shorten.</p> <p>Substrate preparation: <br />The substrate must be load-bearing, sound, have a good <br />key and be free from adhesion inhibiting materials such <br />as release agents, dust, laitance layers etc. Substrate <br />preparation e.g. grit-blasting, shot-blasting or high pressure <br />water jetting (500 – 2,000 bar) is required if no previous <br />concrete repair works have been carried out. <br />Adequately pre-wet the prepared substrate before <br />applying ASOCRET- BIS-1/6 at a time when the substrate <br />is matt-damp. <br />Minimum age of concrete substrate: 28 days <br />Tensile adhesion strength of the <br />concrete substrate: <br />min. 1.5 N/mm2 <br />Product preparation: <br />Dependent on the desired consistency, place approx. 5.0– <br />5.25 l of clean water into a clean mixing bucket and whilst <br />mechanically stirring (drill approx. 300–700 rpm), mix in</p> <p>1/3</p> <p>06/17</p> <p>as much dry powder until a lump free, smooth paste is <br />achieved. The mixing time is approx. 2–3 minutes. Allow <br />to mature for 5 minutes then mix through once again. <br />When mixing larger quantities, use a forced action <br />mixer. Only mix as much material as can be used within <br />the pot life given above.</p> <p>Inotec pump system: <br />Inomix compulsory mixer ZM80 Jet Mix <br />Inobeam F21 light / screw conveyor D8-1.5 <br />Reprofiling spray gun 12 mm <br />Max. Pipe length: 30 m <br />Control nozzle displacement: 0.5 – 1.0 m</p> <p>Application by hand: <br />Apply a scratch coat of ASOCRET-BIS-1/6 to the <br />prepared substrate and then lay to the desired thickness. <br />Striking off the mortar is determined by the application <br />involved using a suitable tool (lath, trowel etc) within the <br />pot life. After leaving for the appropriate length of time, <br />the surface can be finished using a felt-board or spongeboard.</p> <p>Material application: <br />Through the addition of air at the spray nozzle, the <br />mortar is sprayed in a circular manner in order to <br />achieve a clean spray pattern. The first pass of the <br />spray head is to fill holes and cavities and to even out <br />irregularities in the substrate. The second spray pass is <br />to achieve the required thickness and to finish with a <br />suitable smoothing tool.</p> <p>Wet spray application: <br />The surface to be treated must be adequately wetted <br />until matt-damp. <br />Re-profiling with wet spray techniques is carried out <br />after mixing in a compulsory mixer with a suitable feed <br />pump using a 12 mm spray re-profiling gun or a 35/12 <br />mm MAWO nozzle. For an even spray pattern a high <br />output construction compressor (min. 4 m3 air / 4 - 5 bar <br />operating pressure) is a mandatory requirement.</p> <p>Post-treatment: <br />Following the application of ASOCRET-BIS-1/6, it is <br />fundamentally necessary to protect the mortar surfaces <br />from drying out too quickly using suitable measures <br />Keep damp for at least 3–5 days using mist spray <br />nozzles or wet jute sacking as required also covered <br />with polythene sheets. The polythene sheets must be <br />fastened to the area treated, so that air exchange <br />cannot take place. If the area in question is exposed to <br />direct sunlight, draughts, large temperature fluctuations <br />and/or low humidity then after care treatment must be <br />intensified. If it is intended to apply a mineral-based <br />waterproof slurry, then this can be used as an alternative <br />after care treatment after approx. 24 hours.</p> <p>Without compulsory mixer: <br />Pump system: High Comp Power <br />Pump unit: XP 120 <br />Water demand: approx. 160 – 180 l/hr <br />Nozzle: MAWO nozzle 35/12 mm or 12 mm <br />re-profiling spray gun <br />Max. Pipe length: 30 m <br />Control nozzle displacement: 0.5 – 1.0 m <br />PFT pump system: <br />Multi Mix compulsory mixer <br />Feed pump N2FU4000 / screw conveyor D8-1.5 <br />Reprofiling spray gun 12 mm <br />Max. Pipe length: 30 m <br />Control nozzle displacement: 0.5 – 1.0 m</p> <p>Important advice: <br />• Prior to carrying out concrete repair works the <br />actual condition should be inspected by an expert <br />or Structural Engineer. The inspection report is to be <br />given to the applicator prior to commencement of <br />repair work. <br />• Protect surfaces not being treated with <br />ASOCRET-BIS-1/6.</p> <p>2/3</p> <p>06/17</p> <p>• ASOCRET-BIS-1/6 mortar, which has already <br />stiffened should not be re-lifed by adding more water <br />or fresh mortar as there is a risk of inadequate strength <br />development <br />• Applications that are not clearly explained in this <br />technical data sheet may only be carried out <br />after consultation with and written confirmation <br />from the Technical Services Department of <br />SCHOMBURG GmbH & Co. KG. <br />• Dependent on the site, observe the “Additional <br />technical contractual conditions and guidelines for <br />civil engineering buildings” – ZTV-ING. <br />Please adhere to the valid EC Materials Safety Data <br />Sheet (MSDS). <br />GISCODE: ZP1</p> <p>This technical data sheet is a translation from the German language version and does not consider local building codes or legal requirements. It shall be used as general reference for the <br />product. Legally binding is only the German technical data sheet or the latest Data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>3/3</p> <p>SF/CoS/TM</p> <p>06/17</p>
