ESCO-FLUAT TM engl_0513.pdf
1 Halaman
39.4 KB
Download
<h1>ESCO-FLUAT TM engl_0513.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-333 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ESCO-FLUAT </p> <p>Art.-No. 2 04146 <br />Solution for the treatment of salts damaging to buildings</p> <p>Properties: <br />• Concentrate <br />• For the conversion of salts damaging to buildings <br />• F or the prevention of early salt penetration into fresh <br />restoration plasters <br />• Solvent free <br />Areas of application: <br />ESCO-FLUAT is used for the restoration of salt containing <br />masonry work by converting chlorides and sulphates <br />into insoluble or sparingly soluble compounds. This <br />serves as an additional measure beneath THERMOPAL <br />restoration plasters. <br />Technical Data: <br />Basis: <br /> <br />Consumption: <br /> <br />Packaging: <br /> <br />Storage: <br /> <br /> <br /> <br /> </p> <p>aqueous hexafluorosilcate <br />solution <br />treated twice approx. <br />0.4 – 0.5 kg/m² <br />1 kg, 10 kg and 25 kg <br />containers <br />24 months when stored <br />cool and dry but frost free in <br />the original unopened <br />container. Use opened <br />containers promptly.</p> <p>Substrate preparation: <br />The substrate must be load-bearing and free from <br />adhesion inhibiting materials such as release agents, <br />dust or other layers. Remove old render, paint and <br />slurries up to at least 80 cm above the damaged <br />area. Rake out crumbly pointing in masonry work to a <br />minimum of 2 cm deep and thoroughly brush masonry <br />work and joints with a wire brush.</p> <p>Product application: <br />Brush apply one or two coats to the exposed masonry <br />work until saturated (dependent on degree of salt <br />contamination and substrate absorption). <br />Single coat saturation: <br />1 part ESCO-FLUAT and 1 part water <br />Two coat saturation: <br />1. Treatment: 1 part ESCO-FLUAT and 2 parts water <br />2. Treatment: 1 part ESCO-FLUAT and 1 part water <br />Allow at least 7 hours between treatments. Approx 24 <br />hours after the final treatment, sweep off the surface <br />once more. <br />Advice: <br />• When using the product avoid metal containers and <br />equipment at all costs. <br />• When measuring indoor air to BIA 7512 there was <br />evidence to show that there was no air contamination <br />hazardous to health. However when applying to <br />large areas, the internal rooms should be ventilated <br />until application of the restoration plaster. <br />• Clean tools very thoroughly immediately after use <br />with clean water. <br />• Protect areas not being treated. <br />• Wash off splashes immediately. Glass, metals, <br />window frames etc. may be attacked by <br />ESCO-FLUAT. <br />Please observe a current valid EU Health & <br />Safety Data Sheet. <br />GISCODE: GH40</p> <p>This technical data sheet does not consider local building codes or legal requirements. It shall be used as general reference for the product, based on our current knowledge <br />and experience. Legally binding is only the latest Data Sheet from one of our foreign subsidaries inside their sales territory. In any case of uncertainty please consult our <br />technical department for further information. <br />1/1</p> <p>WKD/CoS/JD 05/13</p>
