MONOFLEX-white Technical Data Sheet EN 2918.pdf
3 Halaman
187 KB
Download
<h1>MONOFLEX-white Technical Data Sheet EN 2918.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>MONOFLEX-white </p> <p>Art. No. 2 04308</p> <p>Flexible, white tile adhesive</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold, Germany <br />18 <br />2 04308</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold, Germany <br />18 <br />2 04308-1</p> <p>EN 12004 <br />MONOFLEX-white <br />Cement-based adhesive with increased performance for <br />the installation of tiles in interior and exterior areas</p> <p>EN 12004 <br />MONOFLEX-white 3:1 with UNIFLEX-F <br />Cement-based adhesive with increased performance for <br />the installation of tiles in interior and exterior areas</p> <p>C2</p> <p>In a continuously wet area, e.g. swimming pools walkways <br />and public showers, we recommend 25 kg MONOFLEXwhite in floor areas enhanced with 2.0 kg UNIFLEX-F. <br />On horizontal exterior surfaces, e.g. balconies and <br />terraces, enhance 25 kg MONOFLEX-white with 8.33 kg <br />UNIFLEX-F.</p> <p>C2</p> <p>Reaction to fire: <br />Bond strength, as tensile adhesion strength <br />after dry storage: <br />Durability, as tensile adhesion strength <br />after water immersion: <br />after warm storage: <br />after freeze/thaw cycles: </p> <p>Class E</p> <p>Reaction to fire: <br />Bond strength, as tensile adhesion strength <br />after dry storage: <br />Durability, as tensile adhesion strength <br />after water immersion: <br />after warm storage: <br />after freeze/thaw cycles: </p> <p>≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm²</p> <p>Technical data: <br />Basis: Sand, cement, additives <br />(polymer-modified) <br />Colour: off-white <br />Substrate/ <br />pot life: <br />+5 °C to + 30 °C <br />pot life*): <br />approx. 2 hours <br />Adhesive open time*): approx. 20 minutes <br />Ready for grouting*): after 24 hours minimum <br />Foot traffic after*): <br />after approx. 24 hours <br />Cleaning: Clean immediately after use <br />with water <br />Testing: DIN EN 12004, MPABrauschweig test certificate <br />Consumption: dependent on the substrate and <br />application material, <br />min. 1.3 kg/m2/mm <br />approx. 1.9 kg/m2 <br />with 6 mm notched trowel <br />approx. 2.6 kg/m2 <br />with 8 mm notched trowel <br />approx. 3.2 kg/m2 <br />with 10 mm notched trowel <br />Packaging: <br />25 kg bag <br />Storage: dry, 12 months in the original <br />unopened container, promptly <br />use opened container</p> <p>Class E <br />≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm²</p> <p>4</p> <p>S2</p> <p>N</p> <p>TE</p> <p>MONOFLE</p> <p>C2</p> <p>E</p> <p>-F 3:1 <br />LEX <br />IF</p> <p>hite mit U <br />N <br />-w <br />X</p> <p>12 0 0</p> <p>• In accordance with DIN EN 12004, C2 TE S1 <br />• For interior and exterior use <br />• Smooth and easy to process <br />• High initial adhesion <br />• Good stability <br />Areas of use: <br />MONOFLEX-white is used as a thin-bed mortar for <br />applying vitrified tiles, earthenware and ceramic with low <br />water absorption ≤ 0.5% (porcelain stoneware), clinker, <br />mosaic and colour-sensitive natural stone materials. <br />For application of glass mosaic, enhance with UNIFLEX-F; <br />please also refer to the instructions. <br />MONOFLEX-white is suitable for secure application <br />on all substrates according to DIN 18157, part 1, e.g. <br />concrete, aerated concrete, plaster, cement and calciumsulphate screed/heated screed, masonry work, gypsum <br />fibre boards, etc. and for tiling on SCHOMBURG bonded <br />waterproof systems.</p> <p>*) The values apply to 23 °C and 50 % relative humidity.</p> <p>1/3</p> <p>29/18</p> <p>Notes: <br />• In commercial areas, ASODUR-EK98 / <br />ASODUR-DESIGN should be used for application of <br />glass mosaic on floors or in a continuously underwater <br />area (swimming pools, containers, etc.)! In private <br />areas, glass mosaic on floors or in a continuously <br />underwater area may be applied alternatively with <br />MONOFLEX-white enhanced with 8.33 kg UNIFLEX-F <br />per 25 kg MONOFLEX-white. To apply glass mosaic <br />on walls, every 25 kg of MONOFLEX-white should be <br />enhanced with 2.0 kg UNIFLEX-F. In underwater areas, <br />only suitable glass mosaic may be used for continuously <br />underwater areas. We recommend glass mosaic <br />adhered with carrier material on the front side and <br />a profile on the rear side. Grouting the glass mosaic <br />may take place in swimming pools, water containers <br />14 days*) after application with ASODUR-EK98 or <br />ASODUR-DESIGN at the earliest. Wait at least another <br />7 days*) after completing the grouting before filling <br />the pool. The fresh waterproofing, application, and <br />grouting materials must be protected against moisture <br />until they harden. <br />• If ASOFLEX-AKB is used, use ASODUR-EK98 or <br />ASODUR-DESIGN for tiling! <br />• To apply tiles and boards on highly stressed surfaces <br />in exterior areas (balconies and terraces), the highly <br />elastic bonded waterproof systems AQUAFIN-RS300 <br />and UNIFIX-S3 /-fast should be used! <br />• When laying natural stone and synthetic stone, <br />the product-specific properties of the coating <br />materials (tendency to discolour, curling effects, etc.) <br />and the laying recommendations of the manufacturer <br />must be taken into account. Complete trial adhesions <br />in case of doubt! <br />• To avoid curling effects due to water absorption, we <br />recommend using ASODUR-EK98 or ASODUR-DESIGN <br />when working with agglomerates/synthetic stone! <br />• Prime calcium sulphate bound substrates with <br />ASO-Unigrund-GE or ASOUnigrund-K (mix ratio 1:3 <br />with water)! In case of application on calcium sulphate <br />bound substrates, UNIFIX-AEK is useful to avoid</p> <p>Substrate: <br />The substrate must be dry, load-bearing, adequately <br />level, free of penetrating cracks and free of separating <br />substances, such as oils, paints, laitance layers, and <br />loose particles. They must have a primarily closed <br />surface condition and exhibit strength typical of their type. <br />The substrate, substrate preparation, and application <br />as per DIN 18157, part 1, are authoritative when laying <br />tiles. Prime absorbent substrates with ASO-Unigrund. <br />Calcium sulphate screeds must be roughened, vacuumed <br />and primed with ASO-Unigrund, as with all calcium <br />sulphate bound substrates. Heated screeds must be <br />heated in accordance with recognised standards before <br />installation of coverings. Moisture measurement should <br />be carried out with the CM device to assess whether it is <br />ready for laying on. The CM moisture content max. values <br />• CT ≤ 2.0 % for screed on insulation or a separating <br />layer <br />• CA without a floor heating system ≤ 0.5% <br />• CA with a floor heating system ≤ 0.3% <br />should not be exceeded. <br />The CM measurement must be completed in accordance <br />with the current working instructions FBH-AD from <br />the technical information <br />"Interface coordination with heated floor constructions". <br />Application: <br />Mix MONOFLEX-white with clean water in a clean mixing <br />bucket. <br />Mixing ratio: <br />Approx. 8.75 l water: 25 kg MONOFLEX-white <br />highly deformable mortar, class C2 TE S2: <br />25 kg MONOFLEX-white: 8.33 kg UNIFLEX-F : Mix <br />in 1 l water to set the consistency. <br />Mix again after an activation time of 2 min. Do not mix <br />more adhesive mortar than can be used within the pot <br />life. Spread the mixed mortar evenly across the surface <br />and comb through with a suitable notched trowel to suit <br />the board size. Apply the surfacing materials within the <br />adhesive open time.</p> <p>2/3</p> <p>29/18</p> <p>ettringite formation with residual moistures of 1.0 % with <br />heated or 1.5% per CM with unheated constructions! <br />• Do not add water or new mortar to existing thin-bed <br />mortar that has already set in order to make it workable <br />again, since this would involve a risk of inadequate <br />strength development! <br />• Direct contact between cement tile mortar and <br />magnesite screeds leads to the destruction <br />of the magnesite screeds through a chemical reaction <br />known as "magnesite pouring". Moisture pressure from <br />the rear of the substrate must be prevented through <br />appropriate measures. The magnesite substrate should <br />be mechanically roughened and primed with the epoxy <br />resin ASODUR-V360W plus max. 5 % water (approx. <br />250 g/m²). After a waiting time of approx. 12 to 24 <br />hours at +20 °C, the second coat of ASODUR-V360W <br />should be applied (approx. 300–350 g/m²). While <br />the second coat is still fresh, apply plenty of quartz <br />sand with a grain size of 0.5-1.0 mm. Installation of <br />coverings may be completed after a further waiting time <br />of approx.12-16 hours. <br />• Protect surfaces that are not to be treated from <br />the effects of MONOFLEX-white! <br />• MONOFLEX-white is a hydraulically hardening <br />mortar that can take several days in unfavourable <br />weather influences before being fully hardened, so it <br />must be protected from exposure to water and frost <br />in the meantime. <br />• The current relevant regulations are to be observed! So, <br />for example: <br />DIN 18531, DIN 18534, DIN 18535 <br />DIN 18157, DIN 18352, DIN 18560 <br />EN 13813, DIN 18 202, DIN 1055 <br />The BEB data sheets published by the German <br />Association for Screen and Coverings (Bundesverband <br />Estrich und Belag e.V.) <br />The technical information “Interface coordination <br />for heated floor structures”</p> <p> <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> </p> <p>The ZDB data sheets published by the Technical <br />Association of German Tile Industry: <br />[*1] “Bonded waterproof systems” <br />[*2] “Coverings on calcium sulphate screeds” <br />[*3] “Movement joints in cladding and coverings <br />made of tiles and boards” <br />[*4] “Large format ceramic tiles and boards” <br />[*5] “Ceramic tiles and boards, natural stone <br />and artificial stone on cement-based floor <br />constructions with insulating layers” <br />[*6] “Ceramic tiles and boards, natural stone and <br />artificial stone on heated and cement-based floor <br />constructions” <br />[*7] “Outer coverings” <br />[*8] “Coverings on poured asphalt screed” <br />[*9] “Height differences” <br />[*10] “Tolerances” <br />[*11] “Cleaning, protecting, maintaining” <br />[*12] “Swimming pool construction”</p> <p>Please observe valid EU safety data sheets! <br />GIS CODE: PU 10</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case <br />of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the <br />user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />3/3</p> <p>WKD/TET/TM</p> <p>29/18</p>
