AQUAFIN-WM12 Technical Data Sheet EN 0519.pdf
3 หน้า
79.6 กิโลไบต์
Download
<h1>AQUAFIN-WM12 Technical Data Sheet EN 0519.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>AQUAFIN®-WM12 </p> <p>Art. no. 2 07230</p> <p>PVC-based fresh concrete waterproofing membrane</p> <p>Tear resistance (MD/CMD), <br />in accordance with <br />EN 12310-1: <br />600/600 N</p> <p>• Combined waterproofing and vapour barrier <br />• High bonding <br />• Prevents water ingress behind <br />• Frost-resistant and ageing-resistant <br />• Crack bridging <br />• Plasticiser-free <br />• Suitable for welding and bonding</p> <p>Elongation at break <br />(MD/CMD), in accordance <br />with EN 12311-2: <br />130/80 % <br />Shear resistance of the joint <br />seams, in accordance with <br />EN 12317-2: Failure outside the joint seam</p> <p>Areas of use: <br />For the secure waterproofing of horizontal and/or vertical <br />building components in direct contact with the ground, in <br />above-ground and below-ground construction and in civil <br />engineering, e.g. basement walls, foundations, floor slabs <br />in combination with fresh concrete.</p> <p>Impact resistance <br />in accordance with: <br />EN 12691 procedure A: </p> <p>Reaction to fire, in accordance <br />with EN 13501-1: <br />Class E</p> <p>Technical data: <br />Basis: PVC membrane and special <br />fleece <br />Colour: <br />Transparent/white <br />Width: <br />approx. 1.0 m <br />Length: <br />20 m <br />Thickness (membrane): <br />approx. 1.2 mm <br />Surface weight <br />approx. 1.8 kg/m² <br />Application temp.: <br />-5 °C to +50 °C</p> <p>Storage: Cool, dry and protected from <br />sunlight, min. 18 months in the <br />original unopened container <br />Substrate: <br />The substrate must have adequate load-bearing capability <br />and must be largely flat and pressure-resistant in order to <br />counterbalance the loads that arise during the application <br />and concreting works. Larger surface irregularities or steps <br />must be levelled out beforehand by means of suitable <br />mortar systems or suitable fillers, e.g. sand. <br />In the case of applications underneath floor slabs on <br />compacted, pressure-resistant, capillary-breaking layers, <br />there must be no sharp-edged or pointed components on <br />the surface. <br />Formwork may not deform during the concreting works. In <br />the case of vertical applications, the top finishing rail must <br />be secured using suitable measures.</p> <p>Watertightness in accordance <br />with EN 1928, <br />procedure B 60 kPa/24h): Watertight <br />Water vapour resistance <br />factor (EN 1931): </p> <p>700 mm</p> <p>approx. 29 m</p> <p>Tensile strength (MD/CMD), <br />in accordance with <br />EN 12311-2: <br />1056/1056 N/ 50 mm</p> <p>1/3</p> <p>05/19</p> <p>Application: <br />The substrate must be firm and load-bearing. Overlaps <br />should be established with min. 5 cm, and bonded through <br />hot air-welding or adhered with AQUAFIN-CA.</p> <p>layer. In doing so, direct contact between the AQUAFINWM12 and the compacting machine should be avoided. <br />Application as waterproofing in accordance with <br />DIN 18533: <br />The fresh concrete composite film must be applied with <br />the fleece side to the formwork or substrate, before the <br />concreting. Overlaps must be welded; adhesive bonding <br />is not permissible!</p> <p>Application as waterproofing under floor slabs: <br />The fresh concrete composite film must be applied <br />with the transparent side to the substrate, before the <br />concreting. Apply AQUAFIN-WM12 to the appropriately <br />compacted, pressure-resistant, capillary-breaking layer <br />or blinding layer (concrete or thermal insulation) in <br />overlapping linear sheets. The overlapping width is 5 cm. <br />The joints are bonded by means of hot air welding or <br />adhered with AQUAFIN-CA. Avoid damage during the <br />subsequent work steps, e.g. laying reinforcement. Spacers <br />used shall have a large surface area at the support points. <br />The concreting of the floor slab must be professionally <br />applied and in accordance with the applicable standards <br />and regulations. It is particularly important to ensure <br />that the concreting is implemented free of voids or that <br />bonding is implemented covering the whole area of the <br />fleece layer. In doing so, direct contact between the <br />AQUAFIN-WM12 and the compacting machine should <br />be avoided.</p> <p>Hot air welding: <br />Device parameters: <br />• 220V hot air blower with stepless temperature <br />adjustment up to +600 °C and air flow regulator <br />• Heating power > 1400 Watt <br />• Width slotted nozzle 40 mm (perforated on the underside) <br />The welding of the AQUAFIN-WM12 is carried out <br />with handheld welding devices (e.g. Leister Triac) with <br />a temperature of +450 °C to +650 °C (approx. level <br />6.5). The sealing sheets are laid overlapping and tacked <br />at a max. pitch of 50 cm, parallel with one another. Then <br />the handheld welding device is guided slowly over the <br />joint at an angle of approx. 30°. In doing so, the sheets <br />are pressed together with a moderate force of > 5–6 kp <br />using a silicone roller, parallel with the sheet edge, until <br />a weld seam is created at the joint edges. Welding <br />is implemented over a width of approx. 4 cm. With <br />professionally prepared welding, a weld bead running <br />along the seam can be considered an indication of <br />a perfect joint. The joint seams are immediately leak-proof <br />and are fully cured after 24 hours. <br />Carry out trial welding before the hot air welding work. <br />In the case of applications on thermal insulation, suitable <br />underlays, which will be slowly pulled along with the <br />sheets during welding, should be used. The welding zones <br />are to be cleaned of any adhesion inhibiting substances. <br />In doing so, it is not permitted to use solvents or splice <br />wash.</p> <p>Application as waterproofing in formwork constructions: <br />The fresh concrete composite film must be applied with the <br />transparent side to the formwork, before the concreting. <br />AQUAFIN-WM12 is fitted to the top side of the formwork <br />construction in linear sheets, overlapping and fastened by <br />means of nail strips. The overlapping width is 5 cm. The <br />joints are bonded by means of hot air welding or adhered <br />with AQUAFIN-CA. Avoid damage during the subsequent <br />work steps, e.g. laying reinforcement or spacing struts. The <br />concreting must be professionally applied in accordance <br />with the applicable standards and regulations. It is <br />particularly important to ensure that the concreting is <br />implemented free of voids (gravel pockets) or that bonding <br />is implemented covering the whole area of the fleece</p> <p>2/3</p> <p>05/19</p> <p>Adhered with AQUAFIN-CA: <br />Generously apply AQUAFIN-CA to the overlap area <br />of the substrate and press the next sheet into the fresh <br />adhesive. The concreting process can take place no <br />sooner than 8 hours after adhesion. <br />Notes: <br />• The fresh concrete composite system should be stored <br />dry as a matter of principle. <br />• Do not store sharp objects or pallets on the fresh <br />concrete composite film. <br />• The current applicable regulations and datasheets are <br />to be observed! <br />Please observe valid EU safety data sheets!</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case <br />of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the <br />user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />3/3</p> <p>SE/TET/TaB</p> <p>05/19</p>
