ADF-Dehnfugenband Technical Data Sheet EN 4319.pdf
2 หน้า
74.4 กิโลไบต์
Download
<h1>ADF-Dehnfugenband Technical Data Sheet EN 4319.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ADF®-Dehnfugenband (Expansion-Joint-Tape) </p> <p>Art.-No. 2 05955</p> <p>Elastic sealing tape</p> <p>Substrates: <br />All conventional substrates, which are suitable for the <br />application of waterproof membranes. The substrate must <br />be professionally prepared. All substrates must be sound, <br />load-bearing, free from frost and adhesion inhibiting <br />components. Any voids or irregularities must be levelled <br />with ASOCRET-M30.</p> <p>• Tear resistant <br />• Water impermeable <br />• Compatible with bitumen <br />• Fleece laminated <br />• Highly elastic <br />Areas of application: <br />For forming water impermeable construction expansion <br />joints and for use at junctions between construction <br />elements, e.g. in areas in contact with the ground.</p> <p>Product application: <br />Joint waterproofing at wall/floor junctions and bay <br />movement joints: <br />Apply the waterproof material to both sides of the joint <br />to be bridged to a minimum of 2 cm wider than the <br />ADF-Dehnfugenband (Expansion-Joint-Tape). Lay the <br />ADF-Dehnfugenband (Expansion-Joint-Tape) into the fresh <br />material and press in evenly and without folds. Apply <br />another layer of the waterproof coating over the top. The <br />movement joint area (for the subsequent application of <br />an elastic sealant) can remain free from the waterproof <br />coating. Overlap the edges of the joint tape a minimum <br />of 10 cm and fully bond (solid bed) with the waterproof <br />coating avoiding folds.</p> <p>Technical Data: <br />Basis: composite material <br />fleece – membrane – fleece <br />Colour: grey <br />Thickness: <br />approx. 0.8 mm <br />Bursting pressure: <br />> 4 bar <br />Temperature resistance: -5 °C to +90 °C <br />UV resistance to <br />DIN EN ISO 4892-2: <br />min. 500 hrs <br />Elongation, longitudinal <br />to DIN 527-3: <br />approx. 148% <br />Elongation, transverse <br />to DIN 527-3: <br />approx. 250%</p> <p>Waterproofing structural movement joints continuous <br />through foundation slabs: <br />Lay the ADF-Dehnfugenband (Expansion-Joint-Tape) into <br />the joint forming a loop. Using a suitable waterproof <br />material, bond the tape without voids or folds and bed <br />into the waterproof layer. Where there is water under <br />pressure, additionally insert a suitable closed cell backing <br />strip and bond another layer of ADF-Dehnfugenband <br />(Expansion-Joint-Tape) over the joint with the appropriate <br />waterproof coating and overcoat.</p> <p>Chemical resistance after 7 days storage at +22 °C was <br />achieved with the following chemicals: <br /> Hydrochloric acid 3%, <br />Sulphuric acid 35% <br />Citric acid 100 g/l, <br />Potassium hydroxide 3% <br />Sodium hydroxide 0.3 g/l <br />Salt water 20 g/l (sea salt)</p> <p>For corners and cruciform cross sections, the following <br />pre-formed pieces are available: <br />ASO-Joint-Tape-2000-S-Corners <br />(90° internal and external) <br />ASO-Joint-Tape-2000-T-Piece as well as <br />ASO-Joint-Tape-2000-Cross-Piece</p> <p>Packaging: 50 m long, 15 cm wide <br />50 m long, 25 cm wide <br />Storage: cool and dry, protected from <br />sunlight and weathering, <br />24 months</p> <p>1/2</p> <p>43/19</p> <p>Dependent on the degree of exposure to water, <br />suitable waterproof materials are AQUAFIN-RB400, <br />AQUAFIN-RS300, AQUAFIN-2K/M-PLUS, <br />ASOFLEX-AKB and COMBIDIC-2K-CLASSIC or <br />COMBIDIC-2K-PREMIUM. <br />After bonding the tape, the following alternative <br />waterproof coatings are available for use: <br />COMBIFLEX-C2/P, COMBIFLEX-EL, COMBIDIC-1K and <br />COMBIDIC-2K-CLASSIC or COMBIDIC-2K-PREMIUM. <br />Important advice: <br />• Recognised construction technology regulations are to <br />be followed. <br />• Joints which are to be safeguarded with <br />ADF-Dehnfugenband (Expansion-Joint-Tape) must be <br />adequately protected against mechanical damage. <br />• ADF-Dehnfugenband (Expansion-Joint-Tape) may not <br />be bonded with products containing solvents.</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case <br />of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the <br />user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />2/2</p> <p>SF/CoS/KKa 43/19</p>
