ASODUR-V360W Technical Data Sheet EN 0318.pdf
4 页数
107.9 KB
Download
<h1>ASODUR-V360W Technical Data Sheet EN 0318.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>ASODUR®-V360W</p> <p>Technical Data Sheet <br />INDUFLOOR®-IB2360 </p> <p>Art.-No. 2 05056</p> <p>Water emulsified sealer</p> <p>warehouses, workshops, garages, production areas, <br />access balconies etc. Avoid high point loading. Not <br />suitable for heavy duty areas under high mechanical <br />stresses.</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />15 <br />2 05056 <br />EN 1504-2 <br />ASODUR-V360W</p> <p>Technical Data: <br />Basis: <br />2-comp. epoxy resin <br />Colour: pebble grey (≈ RAL 7032) <br />stone grey(≈ RAL 7030) <br />Special colours: <br />anthracite grey (≈ RAL 7016) <br />oxide red (≈ RAL 3009) <br />light grey (≈ RAL 7035) <br />light ivory (≈ RAL 1015) <br />Other special colours on request <br />Viscosity*: <br />medium viscosity <br />Density*: <br />approx. 1.36 g/cm3 <br />Mixing ratio: <br />100:20 parts by weight <br />Pot life*: <br />approx. 40 minutes <br />Ambient and <br />substrate temp.: min. +10 °C <br />max. +35 °C <br />at max. 65 % relative humidity <br />Foot traffic after*: approx. 16 hours <br />Overcoat after*: approx. 16 hours up to max. 24 hours <br />Fully cured after*: approx. 7 days</p> <p>Surface protection product - Coating <br />Principle 2.2/5.1/6.1 <br />Water vapour permeability <br />Class II <br />Capillary water absorption and <br />water permeability <br />w < 0.1 kg/m² × h0.5 <br />Tensile adhesion strength by pull-off test <br />≥ 1.5 (1.0) N/mm² <br />Abrasion resistance <br />Loss in mass <br /> <br />≤ 3000 mg <br />Impact resistance <br />Class I <br />Resistance to strong chemical attack <br />Visible observations <br /> <br />to ISO 4628/1 <br /> <br />possible only, due <br /> <br />to the very thin film <br />Reaction to fire <br />Class E <br />Hazardous substances <br />In compliance with 5.3 EN 1504-2</p> <p>• Water emulsified, pigmented, 2-comp. epoxy resin. <br />• Free from organic solvents. <br />• Low odour. <br />• Resistant to dilute alkalis and acids, heating oil and <br />petrol. <br />• Can be diluted up to 10% with water (priming). <br />• Water vapour permeable. <br />• Excellent adhesion to to many substrates. <br />• Satin-sheen surface finish. <br />• Water resistant. <br />• Resistant to plasticizers. <br />• Can be produced as an anti-slip finish. <br />When exposed to UV, colour variations – related to <br />the binder – as well as chalking must be anticipated. <br />Permanent exposure to weathering and permanent <br />exposure to wet conditions is to be tested on an individual <br />basis.</p> <p>Shore D hardness: approx. 70</p> <p>Relative humidity: < 75% <br />Water vapour <br />transmission factor: approx. 1 250 μ <br />Cleaning: Thoroughly clean tools immediately <br />after use with water. <br />Packaging: 1 kg, 6 kg, 12 kg and 30 kg <br />containers. Components A and B are <br />delivered at a predetermined mixing <br />ratio. <br />Storage: 12 months when stored dry, cool <br />and frost free above +10° C in the <br />original unopened packaging.</p> <p>Areas of application: <br />ASODUR-V360W is used for sealing cement-based <br />floor areas, magnesite screeds, calcium sulfate screeds <br />and well compacted poured asphalt screeds e.g. in</p> <p>* The values are valid at +23 °C and 50 % relative humidity</p> <p>1/4</p> <p>03/18</p> <p>Substrate preparation: <br />The area to be treated must be: <br />• dry, firm, sound and have a good key <br />• free from separating and adhesion inhibiting <br />substances such as dust, laitance, grease, oil, rubber <br />marks, paint residues and similar</p> <p>Calcium sulfate screed: <br />• Screed quality: DIN EN 13813 CA-C25-F5 <br />• Age: <br />min. 14 days <br />• Tensile adhesion <br />strength: <br />> 1.0 N/mm² <br />• Residual moisture: < 0.5% (carbide hygrometer method) <br />with underfloor heating < 0.3 % <br />(carbide hygrometer method)</p> <p>Dependent on the condition of the substrate to be treated, <br />use suitable preparation methods e.g. shot blasting, <br />scabbling, planing, brushing, sweeping, vacuuming, grit <br />blasting, high pressure washing. Seal existing cracks (e.g. <br />with ASODUR-K900 in accordance with the technical <br />data sheet).</p> <p>Mastic asphalt screed: <br />• Screed quality: AS IC15 <br />• Tensile adhesion <br />strength: <br />> 1.0 N/mm²</p> <p>The following criteria are also to be observed <br />dependent on the particular substrate: <br />Cementitious surfaces: <br />• Concrete: <br />min. C20/25 <br />• Screed quality: DIN EN 13813 min. CT-C35-F5 <br />• Age: <br />min. 28 days <br />• Tensile adhesion <br />strength: <br />1.5 N/mm2 <br />• Residual moisture: 6% (carbide hygrometer method) <br />• Render quality: <br />P III a / P III b <br />• Tensile adhesion <br />strength: approx. 0.8 N/mm² <br />(pre-blended mortar) <br />• Residual moisture: 6% (carbide hygrometer method)</p> <p>Product preparation: <br />Components A (resin) and B (hardener) are delivered <br />at a predetermined mixing ratio. Tip component B into <br />component A. <br />Ensure that the hardener drains completely from its <br />container. Blend both components together with a suitable <br />mixer at approx. 300 rpm (e.g. drill with paddle). It is <br />important to also stir from the sides and the bottom to <br />ensure that the hardener is evenly dispersed. Stir until the <br />mix is homogenous (free from streaks); mixing time approx. <br />5 minutes. The minimum temperature during mixing should <br />be +15° C. Do not use mixed material directly from the <br />packaging. Decant the material into a clean container <br />and mix through thoroughly once again.</p> <p>Magnesia screed: <br />• Screed quality: <br />• Age: <br />• Tensile adhesion <br />strength: <br />• Residual moisture: </p> <p>Method of application / consumption: <br />Apply 2-3 coats of ASODUR-V360W by roller. Pour the <br />mixed material in portions over the area and spread using <br />a twin-bladed rubber squeegee. Then even out using a <br />short nap paint roller in a 90º crossways manner.</p> <p>DIN EN 13813 min. MA-C35-F5 <br />min. 14 days <br />> 1.0 N/mm2 <br />< 2 % (carbide hygrometer method)</p> <p>Priming: Dilute ASODUR-V360W with 8 to a max. of 10% <br />water and apply by roller in one coat (crossways at 90º). <br />Consumption: approx. 300 g/m2 of diluted material.</p> <p>2/4</p> <p>03/18</p> <p>Important advice: <br />• Avoid applying individual coats too thickly (greater <br />material consumption). This leads to crack formation, <br />possibly de-lamination and to extended waiting times <br />between individual applications. <br />• Ensure there is good ventilation during the drying and <br />curing phases. <br />• As a rule SCHOMBURG products are supplied in <br />working packs i.e. at a predetermined mixing ratio. <br />With deliveries in large containers, part quantities will <br />need to be weighed using scales. Always thoroughly <br />stir the filled components and only then blend with <br />the second component. This is to be carried out with <br />a suitable rotary mixer e.g. Polyplan/Ronden mixing <br />paddle or similar. In order to exclude mixing errors, <br />decant into a clean container and remix. The mixing <br />speed should be 300 – 400 rpm. Ensure that no air <br />is entrained. Higher speeds drag unnecessary air <br />quantities into the product whilst lower speeds do not <br />result in a good blend or require too long a mix time <br />(pot life). The temperature of the components should <br />be at a minimum of +15° C. This is also applicable <br />to any fillers, e.g. sand, to be mixed in. The addition of <br />any fillers is carried out after both liquids have been <br />blended. Afterwards tip the completely mixed material <br />immediately onto the prepared substrate and promptly <br />thoroughly spread in accordance with the instructions <br />in the technical data sheet. Always stir one component <br />products before using. <br />• Higher temperatures shorten the pot life. Lower <br />temperatures increase the pot life and curing time. <br />Material consumption is also increased at lower <br />temperatures. <br />• Colour: Minor colour variations due to different <br />production plants and raw material fluctuations are <br />unavoidable. This should be considered when applying <br />coatings. Neighbouring sections should be completed <br />with the same production units (see batch number on <br />the packaging).</p> <p>Possible situation - levelling /scratch coat: <br />Produce the levelling/scratch coat: <br />ASODUR-V360W: 1.0 part by weight <br />Quartz sand (particle size 0.1–0.35 mm) 0.5 parts by weight <br />Mix in the quartz sand with the previously homogenously <br />mixed and decanted resin and hardener components. <br />Ensure that the liquid and solid constituents are evenly <br />blended. <br />Levelling layer and scratch coat: <br />Apply the finished mix in a single operation on the primed <br />surface to a thickness of max. 2 mm using scratch coat <br />techniques. Treat uneven areas as necessary, once <br />cured, with 100 grade abrasive paper without leaving <br />grooves, and vacuum. Once hardened, seal the area with <br />ASODUR-V360W. <br />The consumption dependent on substrate condition is <br />approx. 1.6 kg/m²/mm thickness. <br />Drying time: 1 – 2 days/mm. <br />Recesses and pinholes are to be closed off with <br />ASODUR-V360W with the addition of 2–3% by weight of <br />the fibre filler ASO-FF. A second layer can be applied, if <br />needed, after waiting for approx. 2 hours. <br />Finishing sealer: <br />ASODUR-V360W is roller applied (crossways at 90º) in <br />1–2 coats on to the primer or scratch coat. <br />Consumption: approx. 300–350 g/m2/coat <br />Possible situation - slip prevention: <br />Apply one coat of ASODUR-V360W. Homogenously <br />stir in ASO-Antislide (10% by weight), then thoroughly <br />and evenly apply the mix with a short nap paint roller <br />crossways at 90º. Keep overlap areas as small as <br />possible. <br />Consumption: a <br /> pprox. 140 – 170 g/m² <br />plus 14 – 17 g/m² ASO-AntiSlide</p> <p>3/4</p> <p>03/18</p> <p>• The bond between the individual coats can be <br />heavily impeded through the influence of moisture or <br />contamination between successive applications. The <br />substrate temperature must be a min. of < 3° C above <br />the dew point. <br />• If there is a long time period between coatings or if <br />areas need to be re-coated after a long time period, <br />then the old surface must be well cleaned and <br />thoroughly abraded, after which a completely new <br />pore free sealing coat should be applied. It is not <br />sufficient to simply overcoat. <br />• Surface protective systems must be protected for <br />approx. 4 – 6 hours from dampness after application <br />(e.g. rain, melt water). Dampness produces a white <br />discolouration and/or stickiness on the surface and <br />can impede the cure. Discoloured and/or sticky <br />surfaces should be taken off e.g. by abrading and <br />renewed. <br />• Consumption quantities given are values determined <br />by calculation without additions for surface roughness <br />or absorption, levelling or residues in the containers. <br />We recommend adding a calculated safety factor of <br />10% to the computed consumption quantities. <br />• Applications that are not clearly explained in this <br />technical data sheet may only be carried out after <br />consultation with and written confirmation from the <br />Technical Services Department of SCHOMBURG. <br />• Cured product residues are to be disposed of under <br />waste disposal classification AVV 150106. <br />Please observe a valid EU safety data sheet. <br />GISCODE: RE 2</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>4/4</p> <p>CJ/CoS/TM</p> <p>03/18</p>
