INDU-Primer-N_GB_TM_1017.pdf
2 页数
51.2 KB
Download
<h1>INDU-Primer-N_GB_TM_1017.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>INDU-Primer-N ASO -Primer-2000/PRIMER-2000 <br />®</p> <p>Art.-No. 2 06406</p> <p>Primer/Adhesion promoter</p> <p>• Very good adhesion to non-porous substrates. <br />• Contains solvent <br />Areas of application: <br />INDU-Primer-N is used as an adhesion promoter for <br />reaction resins, e.g. ASOFLEX-AKB, sealants such as <br />INDUFLEX-MS, INDUFLEX-PS and INDUFLEX-PU and <br />coatings as well as with non-absorbent substrates e.g. <br />mild steel, stainless steel, aluminium, cooper, zinc, glass, <br />clinker, glazed ceramic, PVC, polyester and melamine <br />resin. <br />Technical Data: <br />Basis: one component based on silane <br />Colour: colourless <br />Density: <br />approx. 0.8 g/cm3 <br />Application <br />temperature: <br />+5° C to +30° C <br />*) <br />Flash off time : min. 10 minutes; <br />max. working time approx. 6 hours. <br />Material <br />consumption: max. 10 ml per m2 <br />Cleaning: Work tools must be carefully cleaned <br />immediately after use with the <br />appropriate cleaner e.g. acetone. <br />Packaging: <br />1 litre tin <br />Storage: Cool and dry above +5° C, <br />18 months in the original unopened <br />container. Use opened containers <br />promptly. <br />Substrate: <br />See areas of application. <br />The surface to be treated must be: <br />• Dry, sound, load bearing and have a good key. <br />• Free from separating and adhesion inhibiting <br />substances.</p> <p>Application: <br />INDU-Primer-N is supplied ready for use. Briefly shake <br />the contents of the bottle before use. <br />Method of application/consumption: <br />Priming the joint edges or edge of the joint unit: <br />1. B <br /> ackfill the prepared joint cross section with a closed <br />cell backing strip; ensure that the backing strip does <br />not become damaged. Bonding on three sides is to <br />be prevented by inserting a polythene strip at the <br />base of the joint. <br />2. E venly apply INDU-Primer-N in one operation with a <br />priming brush. <br />Material consumption: approx. 10 g/m2 <br />After waiting for a minimum of 10 minutes*) up to a <br />maximum of 6 hours joint sealing can be carried out <br />by extruding INDUFLEX-MS, INDUFLEX-PS or <br />INDUFLEX-PU. <br />*)</p> <p>These values relate to +23° C and 50% relative humidity.</p> <p>Important advice: <br />• The material contains solvent. When working in <br />confined spaces ensure that there is adequate <br />ventilation and extraction. <br />• Protect areas not being treated from the effects of <br />INDU-Primer-N. <br />• Higher temperatures decrease and lower <br />temperatures increase the application and curing <br />time. <br />• The bond between the individual coats can be <br />heavily impeded through the influence of dampness <br />or contamination between individual applications. <br />• When longer waiting times occur between <br />application of the coats, the surface must be well <br />cleaned and thoroughly abraded, after which a <br />completely new priming coat should be applied.</p> <p>1/2</p> <p>10/17</p> <p>• INDU-Primer-N must be protected from dampness <br />after application (e.g. rain, melt water). Dampness <br />damages the cured primer film. Damaged surfaces <br />must be removed e.g. by abrading and re-coated. <br />• Applications that are not clearly explained in this <br />technical data sheet may only be carried out after <br />consultation with and written confirmation from the <br />Technical Services Department of SCHOMBURG. <br />Please observe a valid EU Health & Safety data sheet.</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding is only the German technical data sheet or the latest Data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>Höl/CoS/TM</p> <p>10/17</p>
