AQUAFIN-P1 Technical Data Sheet EN 3517.pdf
2 ទំព័រ
552 KB
Download
<h1>AQUAFIN-P1 Technical Data Sheet EN 3517.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>AQUAFIN®-P1 </p> <p>Art.-No. 2 05090</p> <p>PU-injection resin for water-bearing cracks</p> <p>• single component highly reactive polyurethane resin <br />• with integrated catalyst <br />• ready to use <br />• very high foam volume on water influx <br />• rapid, visco-plastic and solid foam formation <br />• for the temporary sealing of cracks, with penetrating <br />water <br />• resistant to a range of acids and alkalis <br />• compatible with bitumen <br />Areas of application: <br />AQUAFIN-P1 is used for injecting water-bearing cracks <br />and joints in concrete and stonework. <br />AQUAFIN-P1 is used to:</p> <p>• Stop water influx from cracks, joints and similar <br />• Consolidate loose stonework <br />AQUAFIN-P1 fulfills the requirements of the DiBt data <br />sheet from Nov. 2000, “Assessment of the effects of <br />construction products on concrete and ground water”. <br />Technical Data:</p> <p>Basis:</p> <p>Colour: <br />Viscosity at +5 °C: <br />Viscosity at +10 °C: <br />Viscosity at +15 °C: <br />Viscosity at +25 °C: <br />Density*: <br />Minimum reaction temp: <br />Recommended <br />application temperature:</p> <p>Water reactive one <br />component polyurethane <br />resin (with integral catalyst) <br />brown <br />approx. 2900 ± 300 mPa.s <br />approx. 2100 ± 200 mPa.s <br />approx. 1200 ± 100 mPa.s <br />approx. 425 ± 75 mPa.s <br />approx. 1.150 ± 40 g/cm3 <br />at +25 °C <br />> +5 °C</p> <p>Reaction time **: <br /> <br />Start time at +5 °C: <br />approx. 27 sec. <br /> <br />Start time at +10 °C: <br />approx. 26 sec. <br /> <br />Start time at +15 °C: <br />approx. 24 sec. <br /> <br />Start time at +20 °C: <br />approx. 22 sec. <br /> <br />Start time at +25 °C: <br />approx. 20 sec. <br /> <br />Foamed up at +5 °C: approx. 4 min. 20 sec. <br /> <br />Foamed up at +10 °C: approx. 3 min. 20 sec. <br /> <br />Foamed up at +15 °C: approx. 2 min. 50 sec. <br /> <br />Foamed up at +20 °C: approx. 2 min. 20 sec. <br /> <br />Foamed up at +25 °C: approx. 2 min. 00 sec. <br />Note: The reaction times were determined by adding <br />10% water. <br />*) At +23°C and 50% relative humidity <br />**) The determination of the reaction time is carried out through the addition of <br />10% water, foaming factor at the listed temperatures approx. 30–50. With <br />free foaming: the reaction times, quantity of foam and the properties of the <br />foam are dependent on the water quantity, the surface of the edge of the <br />crack or rock, their distribution in AQUAFIN-P1, pressure and other factors.</p> <p>Cleaning:</p> <p>Packaging:</p> <p>Storage:</p> <p>+15 °C to +30 °C</p> <p>1/2</p> <p>Clean tools thoroughly after use with <br />ASO-R001. At the end of work or where <br />there are lengthy interruptions in work, <br />clean the injection equipment. Do not <br />allow material residues to dry in the <br />machinery and harden. <br />Any cleaning agent or solvent must have <br />a flash point above +21°C. Please <br />follow the guidelines from the machine <br />manufacturer. <br />1.1 and 5.5 kg <br />AQUAFIN-P1 is ready to use with no <br />need to mix. <br />Frost free, cool and dry ≥ +10 °C <br />to +25 °C, 24 month, in the original <br />unopened packaging. Use opened <br />packagings promptly.</p> <p>35/17</p> <p>Substrate preparation:</p> <p>Appropriate to the particular substrate, the following <br />criteria are also to be fulfilled: <br />• Concrete quality: <br />min. C20/25 <br />Tensile adhesion strength: ≥ 1.5 N/mm² <br />Age: <br />min. 28 days <br />• Screed quality: <br />min. EN13813 CT-C35-F5 <br />Tensile adhesion strength: ≥ 1.5 N/mm² <br />• Render quality: <br />P III <br />Tensile adhesion strength: approx. 0.8 N/mm² <br />Product preparation: <br />AQUAFIN-P1 reacts with the moisture in the air and <br />with water. For this reason a skin may form with opened <br />containers but this does not affect the injection. <br />AQUAFIN-P1 is usually injected through packers and <br />either hand or motor driven pumps into the waterbearing area. On contact with water AQUAFIN-P1 <br />foams extensively and hardens. <br />If there is too little water in the area to be waterproofed, <br />then the reaction and hardening processes can be <br />supported by either pre-injecting or post-injecting with <br />water. <br />We recommend, prior to application, that the product <br />is stored for at least 12 hours at a minimum temperature <br />of +15 °C in order to ensure that the recommended <br />application temperature of +15 °C to +30 °C is <br />achieved.</p> <p>• Once the injection resin has cured, remove the <br />injection packers, as necessary and close off the <br />bore holes with ASOCRET-M30 and level off with <br />the concrete surface. <br />For application with suitable injection equipment, we <br />recommend contacting HTG HIGH TECH Germany <br />GmbH in Berlin, www.hightechspray.de. <br />Important advice: <br />• Protect areas which are not to be treated against the <br />influences of AQUAFIN-P1. <br />• The given consumption rates are calculated <br />values without addition for surface roughness and <br />absorption, levelling and residual material in the <br />packaging. We recommend adding a calculated <br />safety factor of 10 % to the consumption rates. <br />• Applications, which are not clearly mentioned in <br />this technical data sheet, may only be carried out <br />following consultation with and written confirmation <br />from SCHOMBURG Technical Services. <br />• Cured product can be disposed of under waste code <br />AVV 150106. <br />Please observe a valid EU Health & Safety data sheet. <br />GISCODE: RU40</p> <p>Method of application / consumption: <br />• Drill into the existing cracks (crack width approx. <br />0.2 mm) at approx. 20 cm intervals. <br />• Clean the boreholes of drilling dust using oil-free <br />compressed air. <br />• Place the injection packers. <br />• Inject AQUAFIN-P1 with appropriate injection <br />equipment. <br />Consumption: approx. 1,150 g/l.</p> <p>This technical data sheet is a translation from the German language version and does not consider local building codes or legal requirements. It shall be used as general reference for the <br />product. Legally binding is only the German technical data sheet or the latest Data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>CJ/CoS/TM</p> <p>35/17</p>
