SANIFIN_GB_TM_3216.pdf
6 ទំព័រ
162 KB
Download
<h1>SANIFIN_GB_TM_3216.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>SANIFIN</p> <p>Art.-No 2 05901</p> <p>v er</p> <p>Properties: <br />•V <br /> ery low emissions <br />•W <br /> ater impermeable <br />•C <br /> rack bridging <br />•A <br /> lkali resistant <br />• R esistant to chemicals in <br />accordance with building <br />authorities test criteria <br />• Composite material <br />• F or interiors <br />•U <br /> V stabilised <br />• R esistant to micro organisms <br />•E <br /> asy to use <br />•E <br /> ven thickness <br />•B <br /> uilding authorities tested</p> <p>y lo</p> <p>io n</p> <p>Waterproof membrane beneath tiles</p> <p>w e m is</p> <p>s</p> <p>SCHOMBURG <br />GmbH & Co.KG <br />Detmold <br />P-1201/015/16-MPA BS <br />MPA-Braunschweig</p> <p>Areas of application: <br />SANIFIN is used for waterproofing beneath ceramic tile, <br />natural stone and synthetic stone finishes in bathrooms, <br />kitchens, private and public wash rooms (such as e.g. <br />in hotels, sports complexes and old peoples homes and <br />care homes). <br />SANIFIN is suitable for wet duty classification areas <br />A and C in accordance with building authority test <br />criteria and the damp duty classification areas A0 in <br />accordance with the ZDB information sheet “Advice <br />on the installation of bonded waterproofing with tiled <br />finishes in internal and external areas.” <br />Furthermore SANIFIN can be used for waterproofing <br />in buildings with traffic loadings up to 3.5 KN/m2, <br />point loads in accordance with DIN 1055-3 up to <br />2KN. High dynamic loading (such as e.g. continuous <br />vehicular traffic) is excluded. <br />Fine, non-penetrating hairline cracks on the surface of <br />the substrate of < 0.1 mm are acceptable and can be <br />directly bridged with SANIFIN. <br />SANIFIN is suitable for use in interiors in accordance <br />with the AgBB evaluation scheme (Committee for <br />Health-related Evaluation of Building Products), the <br />French VOC by-law and GEV-EMICODE.</p> <p>Technical Data: <br />Basis: <br />composite material consisting <br /> <br />of a polypropylene fleece on <br /> <br />the exterior with an internal <br /> polyethylene inlay <br />Weight: <br />approx. 275 g/m² <br />Colour: <br />white with random print <br />Sd value: <br />≥ 85 m <br />Water vapour permeability <br />in accordance with EN 1931 <br />Thickness: <br />approx. 0.6 mm <br />Storage: <br />frost free, 18 months, <br /> <br />protected from sunlight in the <br /> original unopened packaging <br />Packaging: <br />Rolls: 15 m x 1.00 m <br /> (length x width) <br />Fire performance to <br />DIN 4102: <br />B2 <br />UV resistance to <br />DIN ISO 4892-3: <br />≥ 450 hours <br />Testing: <br />Fulfills the requirements of the <br /> <br />“Testing policy for the <br /> <br />assignation of a building <br /> <br />authorities test certificate for <br /> <br />waterproofing materials in <br /> <br />combination with tiled <br /> <br />finishes, part 2 sheet form <br /> combination waterproofing” <br /> <br />for the procurement of an <br /> abP. <br /> <br />MPA Braunschweig, test <br /> certificate No. <br /> P-1201/015/16-MPA BS <br />System components for wet duty classes <br />A1, A0: <br />ASO-Unigrund-GE, ASO-Unigrund-K (mix ratio 1:3) <br />or ASO-Unigrund-S, overlap SANIFIN and bond with <br />SOLOFLEX, MONOFLEX-XL, MONOFLEX-FB. <br />ASO-Joint-Tape-2000 and also available as shapes <br />ASO-Joint-Tape-2000 corners, 90°, internal/external, <br />ASO-Joint-Tape-2000-S corners, 90°, internal/external,</p> <p>1/6</p> <p>32/16</p> <p>ASO-Joint-Tape-2000-T pieces, <br />ASO-Joint-Tape-2000-crossover, <br />ASO-Joint-Sleeve-floor and <br />ASO-Joint-Sleeve-wall. <br />SOLOFLEX, MONOFLEX-XL, MONOFLEX-FB for <br />bonding the waterproof tape sections and tiles. <br />ASO-Primer-2000 as an adhesion promoter to <br />connections/flanges. <br />AQUAFIN-RS300 for attaching the <br />ASO-Joint-Sleeve-floor/wall to thin bed flanges pipe <br />penetrations. <br />ASO-Fugenbunt/CRISTALLFUGE PLUS/ASO-Flexfuge/ <br />HF05-Brillantfuge/ASODUR-EK98/ASODUR-Design <br />for grouting the finish. <br />ESCOSIL-2000, ESCOSIL-2000-ST, <br />ESCOSIL-2000-UW for sealing movement joints.</p> <p>Substrate: <br />All flat, load bearing surfaces that are capable of taking <br />a tiled finish are suitable and that are suited to accept <br />a tiled combination waterproof membrane (see ZDB <br />information sheet [*1]).</p> <p>Wet duty class C <br />(including the above classifications): <br />ASO-Unigrund-GE, ASO-Unigrund-K (mix ratio 1:3) or <br />ASO-Unigrund-S <br />Bond SANIFIN with SOLOFLEX, MONOFLEX-XL, <br />MONOFLEX-FB. <br />ASO-Joint-Tape-2000-S and also available as shapes <br />ASO--Joint-Tape-2000-S corners, 90°, internal/external, <br />ASO--Joint-Tape-2000-T pieces, <br />ASO--Joint-Tape-2000-crossover, <br />ASO-Joint-Sleeve-floor and <br />ASO-Joint-Sleeve-wall. <br />ASOFLEX-AKB-wall for bonding the joint tape <br />sections, ASO-Joint-Sleeve-floor/wall to thin bed <br />flanges, pipe penetrations, overlapping and straight cut <br />joint tape between the membrane sheets. <br />ASO-Primer-2000 as an adhesion promoter to <br />connections/flanges. <br />ASODUR Design, ASODUR-EK98 for installing the tiles. <br />HF05-Brillantfuge/ASODUR-EK98/ASODUR-Design <br />for grouting the finish. <br />INDUFLEX-VK6060, ESCOSIL-2000, ESCOSIL-2000-ST, <br />ESCOSIL-2000-UW for movement joints.</p> <p>Renders to EN 998-1 of strength classification CS I to <br />CS IV must have a minimum compressive strength of <br />2.0 N/mm2 and be suitable for taking tiles in the <br />relevant dampness/wet duty classification. The surface <br />should remain rough and not felted or smoothed.</p> <p>The substrate must be load bearing, suitably flat, free <br />from penetrating cracks and free from separating <br />substances (such as e.g. oil, paint, laitance and loose <br />debris). The substrate must have a largely closed tight <br />surface and have a surface condition and strength <br />appropriate for its type. With regard to the substrate, <br />substrate preparation and application to DIN 18 <br />157, part 1 is overriding. Separating cracks are to be <br />professionally appraised and if necessary sealed with <br />an adhesive seal (e.g. with ASODUR-K900) before <br />further work.</p> <p>Prime porous and lightly porous substrates with <br />ASO-Unigrund. Steps in the substrate and dampness <br />penetration from the rear are to be eliminated. <br />Irregularities are to be appropriately evened out prior to <br />the installation of SANIFIN. This levelling can be carried <br />out with e.g. the levelling compound SOLOPLAN-30, <br />SOLOCRET-50 or SOLOCRET-15. <br />In damp/wet duty areas a fall of minimum 1.5% is to <br />be constructed towards the drain outlet. <br />Floor drain outlets should be furnished with a <br />circumferential thin bed flange of a minimum width of <br />5 cm and consist of a material suitable for bonding <br />(such as e.g. stainless steel, gunmetal, PVC-U). <br />Heated screeds must be commissioned prior to <br />the installation of floor finishes in accordance with <br />recognised technical regulations. To determine the <br />readiness of substrates to receive finishes carry out</p> <p>2/6</p> <p>32/16</p> <p>moisture measurements with a CM device. The CM <br />moisture content may not exceed: <br />• CT ≤ 2.0 CM% for screeds on insulation or separating <br />layers <br />• CA without underfloor heating ≤ 0.5 CM% <br />• CA with underfloor heating ≤ 0.3 CM% <br />The CM measurement is to be carried out in <br />accordance with current work instructions FBH-AD from <br />the technical information “Coordination of cut out areas <br />for heated floor construction”. <br />Calcium sulphate screeds are acceptable in housing <br />construction with floor drains. They must be abraded, <br />vacuumed and as with all calcium sulphate based <br />substrates, primed with ASO-Unigrund.</p> <p>4)</p> <p>5)</p> <p>Application: <br />Construction in wet duty classification <br />areas A1</p> <p>Wall and floor areas with lower to higher <br />levels of wet use (such as e.g. private <br />bathrooms, WCs and kitchens, communal <br />showers in sports complexes, care homes, <br />health centres, swimming pool surrounds etc.)</p> <p>1) A <br /> ssess the substrate, clean and prepare <br />appropriately. Roughen edging profiles, thin bed <br />flanges as necessary, clean and degrease with <br />Universal cleaner. Prime porous and lightly porous <br />substrates with ASO-Unigrund-GE or ASO-Unigrund-K <br />(mix ratio 1:3 with water). <br />2) Place SOLOFLEX, MONOFLEX-XL, or for use on <br />floors, MONOFLEX-FB, into a clean mixing bucket <br />and mix to a homogenous consistency with a drill <br />and paddle (approx. 300–700 rpm). Use a smooth, <br />free flowing consistency to install the waterproof <br />membrane in order to achieve good wetting out of <br />the SANIFIN. Follow the technical data sheet for the <br />selected thin bed adhesive! <br />3) Cut the SANIFIN to fit using a knife or scissors. <br />Comb the thin-bed adhesive onto the prepared <br />substrate using a 4 mm notched trowel approx. 10 <br />cm wider than the SANIFIN membrane. Subsequently <br />lay the membrane into the adhesive bed and press <br />firmly into the adhesive bed, without voids or folds,</p> <p>6)</p> <p>7)</p> <p>3/6</p> <p>with a plasterers trowel or a roller. Ensure that there <br />is void free bedding and good wetting between <br />the fleece and the adhesive. The cut membrane <br />should be overlapped a minimum of 5 to 10 cm. <br />Bonding of the membrane in the overlapped areas <br />is also to be carried out with the water repellent <br />ADF-Systemkleber. The membrane should be laid in <br />shingle fashion in the direction of the drainage. <br />Joints / junctions are to be carried out on the top <br />surface of the SANIFIN with ASO-Joint-Tape-2000 as <br />well as formed pieces ASO-Joint-Tape-2000-corners, <br />90°, internal/external, ASO-Joint-Tape-2000-S <br />corners, 90°, internal/external, ASO-Joint-Tape2000-T pieces, ASO-Joint-Tape-2000-crossover. <br />Bond ASO-Joint-Tape-2000 or ASO-Joint-Tape2000-corners (internal and external) in the corners, <br />at the transition between wall and floor as well as <br />over connection joints, with AQUAFIN-RS300 (or <br />on bonded screeds with the thin bed adhesive used) <br />without voids or folds on the SANIFIN and on the <br />prepared wall surface.The pre-formed sections <br />ASO-Joint-Tape-T pieces or ASO-Joint-Tape crossovers <br />are available for crossing structural or general <br />movement joints, that when folded into the joint in a <br />loop makes this possible. Straight joints are always to <br />be overlapped between 5 and 10 cm. Ensure that a <br />watertight connection between the wall and the floor <br />waterproofing is produced. <br />Floor drains are to be prepared as described in 1 <br />and must be furnished with a suitable thin bed flange. <br />With a clean cloth, thinly wipe ASO-Primer-2000 <br />adhesion promoter on to the stainless steel, red <br />brass, PVC-U thin bed flange. After 30 minutes <br />and up to a maximum of 4 hours continue with the <br />following steps. Trowel AQUAFIN-RS300 using a 6 <br />mm notched trowel onto the thin bed flange and in <br />overlapped areas onto the SANIFIN. Before this coat <br />forms a skin bed in ASO-Joint-Sleeve-floor with no <br />voids or folds so that a watertight connection to the <br />SANIFIN is produced. <br />For waterproofing pipe penetrations in wall areas <br />either ASO-Joint-Sleeve-floor or ASO-Joint-Sleeve-wall <br />is used dependent on the nominal diameter. Roughen <br />pipe penetrations, clean and degrease with a <br />suitable cleaner. Then thinly wipe with</p> <p>32/16</p> <p>ASO-Primer-2000 as an adhesion promoter using a <br />clean cloth. After 30 minutes and up to a maximum <br />of 4 hours thoroughly apply AQUAFIN-RS300 and <br />subsequently position the ASO-Joint-Sleeve. The hole <br />diameter of the gasket must be considerably smaller <br />than the diameter of the pipe so that via a “memory <br />effect” the ASO-Joint-Sleeve applies pressure to the <br />pipe penetration. <br />8) The tiles for the floor finish must have a minimum <br />surface area of 100 cm2 and a minimum of <br />1500 N breaking load. As far as possible, install <br />the tiles or slabs in a void free bed with the selected <br />thin bed adhesive within the open time. Produce a <br />scratch coat on the SANIFIN and subsequently comb <br />out the adhesive evenly with a suitable notch size <br />dependent on the size of the tile. The installation <br />of tiles can be carried out directly onto the freshly <br />laid SANIFIN, if the waterproofing is adequately <br />protected and any load spread (e.g. protective <br />boards). <br />9) T he grouting of the tiled finish can be carried out <br />with ASO-Fugenbunt, ASO-Flexfuge, the high <br />strength HF05-Brillantfuge or the epoxy resin grout <br />ASODUR-EK98/ASODUR-Design. For grouting <br />natural stone we recommend CRISTALLFUGE PLUS <br />with rapid crystalline water binding. Leave movement <br />joints free for elastic sealing. <br />10) Sealing of connection and movement joints is <br />carried out with ESCOSIL-2000 or <br />ESCOSIL-2000-T with natural stone. <br />Construction in wet duty classification areas C</p> <p>Wall and floor areas with higher levels of <br />wet use and limited chemical contact, (such as <br />e.g. commercial kitchens, dairies, breweries, <br />slaughter houses, car washes etc.)</p> <p>1) A <br /> ssess the substrate, clean and prepare <br />appropriately. Roughen edging profiles and thin <br />bed flanges, clean and degrease with a suitable <br />cleanser. Prime porous and lightly porous substrates <br />with ASO-Unigrund. <br />2) Place SOLOFLEX, MONOFLEX-XL, or for use on <br />floors, MONOFLEX-FB, into a clean mixing bucket <br />and mix to a homogenous consistency with a drill <br />and paddle (approx. 300–700 rpm). Use a smooth,</p> <p>free flowing consistency to install the waterproof <br />membrane in order to achieve good wetting out of <br />the SANIFIN. Follow the technical data sheet for the <br />selected thin bed adhesive! <br />3) Cut the SANIFIN to fit using a knife or scissors. <br />Using a 4 mm notched trowel, comb out the selected <br />thin bed adhesive on to the prepared substrate <br />approx. 10 cm wider than the width of the SANIFIN <br />membrane. Subsequently lay the membrane into the <br />adhesive bed and press firmly into the adhesive bed, <br />without voids or folds, with a plasterers trowel or <br />a roller. Ensure that there is void free bedding and <br />good wetting between the fleece and the adhesive. <br />The watertightness between the individual <br />components of the SANIFIN membrane within <br />waterproof class C can be achieved in the <br />following two variations:</p> <p>3a) T he cut membrane should be overlapped a <br />minimum of 5 to 10 cm. Bonding the membrane <br />in overlap areas is carried out with the PU <br />waterproofing material ASOFLEX-AKB-Wall, once <br />the thin bed adhesive has hardened. The membrane <br />should be laid in shingle fashion in the direction of <br />the drainage. <br />3b) The cut membrane is laid butt jointed with no <br />overlap. In the middle of the butt joint – after the <br />ADF-Systemkleber had hardened – ASO-Joint-Tape2000-S is positioned with the PU waterproofing <br />material ASOFLEX-AKB-wall. <br />4) Joints / junctions are to be carried out on the top <br />surface of the SANIFIN with ASO-Joint-Tape-2000-S <br />as well as formed pieces ASO-Joint-Tape-2000S-corners, 90°, internal/external, ASO-Joint-Tape2000-T pieces, ASO-Joint-Tape-2000-crossover. <br />5) Bond ASO-Joint-Tape-2000-S and ASO-JointTape-2000 corners (internal and external) in the <br />corners, at junctions between wall and floor as well <br />as over connection joints, free from voids and folds <br />with ASOFLEX-AKB-wall to the SANIFIN membrane <br />and the prepared wall surface. The pre-formed <br />sections ASO-Joint-Tape-T pieces or ASO-Joint-Tape <br />crossovers are available for crossing structural or <br />general movement joints, that when folded into the <br />joint in a loop makes this possible. Straight joints are <br />always to be overlapped between 5 and 10 cm.</p> <p>4/6</p> <p>32/16</p> <p>Ensure that a watertight connection between the <br />wall and the floor waterproofing is produced. <br />6) Floor drains are to be prepared as described in 1 <br />and must be furnished with a suitable thin bed flange. <br />With a clean cloth, thinly wipe ASO-Primer-2000 <br />adhesion promoter on to the stainless steel, red brass, <br />PVC-U thin bed flange. After 30 minutes and up to <br />a maximum of 4 hours continue with the following <br />steps. Trowel ASOFLEX-AKB using a 4 mm or 6 <br />mm notched trowel onto the thin bed flange and in <br />overlapped areas onto the SANIFIN. Before this coat <br />forms a skin bed in ASO-Joint-Sleeve-floor with no <br />voids or folds so that a watertight connection to the <br />SANIFIN is produced. <br />7) For waterproofing pipe penetrations in wall <br />areas either ASO-Joint-Sleeve-floor or <br />ASO-Joint-Sleeve-wall is used dependent on the <br />nominal diameter. We recommend manifold <br />penetrations or cable feeders with a 5 cm wide <br />flange are provided to ensure a faultless, rapid <br />installation. Roughen pipe penetrations and flanges, <br />clean and degrease with a suitable cleaner. Then <br />thinly wipe with ASO-Primer-2000 as an adhesion <br />promoter using a clean cloth. After 30 minutes <br />and up to a maximum of 4 hours thoroughly apply <br />ASOFLEX-AKB-wall and subsequently position the <br />ASO-Joint-Sleeve. In that no thin bed flange was <br />designed, the hole diameter of the gasket must be <br />considerably smaller than the diameter of the pipe <br />so that via a “memory effect” the ASO-Joint-Sleeve <br />applies pressure to the pipe penetration. <br />8) The tiles for the floor finish must have a minimum <br />surface area of 100 cm2 and a minimum of 1500 N <br />breaking load. Install the tiles with ASODUR Design <br />or ASODUR-EK98 within the open time ensuring a <br />void free bed as far as possible. Produce a scratch <br />coat on the SANIFIN and subsequently comb out the <br />adhesive evenly with a suitable notch size dependent <br />on the size of the tile. The installation of tiles can be <br />carried out in the floor area, as soon as the thin-bed <br />adheasvie with which the SANIFIN membrane was <br />laid has hardened, as a rule on the next day. <br />On walls tiles can be fixed to SANIFIN with <br />MONOFLEX-XL, on floors, dependent on the <br />mechanical loading or chemical exposure with</p> <p>MONOFLEX-XL as necessary. Information on the type <br />of mechanical stresses and their intensity is to be <br />provided by the planner. The technical service team <br />of SCHOMBURG is on hand to give advice in these <br />situations. <br />9) The grouting of the tiled finish can be carried out with <br />the high strength HF05-Brillantfuge or the epoxy resin <br />grout ASODUR-EK98 or ASODUR-Design. Leave <br />movement joints free for elastic sealing. <br />10) Sealing of connection and movement joints <br />is carried out with INDUFLEX-VK6060, <br />ESCOSIL-2000 or ESCOSIL-2000-UW. <br />Advice: <br />• Waterproofing with the SANIFIN system is classed <br />as an extraordinary construction type. We therefore <br />recommend obtaining contractual agreement. <br />• SANIFIN may not be bonded, overcoated or come <br />into contact with solvent containing adhesives. <br />• Apply a scratch coat to the prepared load-bearing <br />and cleaned substrate for tiling consisting of 25 <br />kg SOLOFLEX, MONOFLEX-XL or for use in floor <br />areas MONOFLEX-FB, each modified with 4.17 kg <br />UNIFLEX-B. Then using this mix, bond SANIFIN to the <br />substrate for tiling, prepared as previously described, <br />or the SANIFIN membrane to the cured scratch coat <br />with the selected thin bed adhesive without additional <br />modification. <br />• Direct contact with metals such as copper, zinc and <br />aluminium is eliminated by a thorough priming within <br />the pores. A pore free priming is produced in two <br />coats with ASODUR-GBM. Apply the first coat to <br />saturation on the cleaned substrate and thoroughly <br />brush in. Once this coat has sufficiently reacted, that <br />it can no longer be spread (approx 3 hrs), spread <br />on a second coat of ASODUR-GBM and broadcast <br />with 0.1-0.6 mm quartz sand. Consumption: approx. <br />800-1000 g/m2 ASODUR-GBM. <br />• Bay, intermediate and structural movement joints are <br />to be brought through or constructed in the designated <br />place and stopped with a suitable material e.g. <br />edging strips. Control joints are to be adhesively filled <br />or ensured against height offsets and formed as a <br />movement joint in the final finish. <br />• As additional protection against ettringite formation</p> <p>5/6</p> <p>32/16</p> <p>with calcium sulphate based substrates in wet duty <br />exposure class A0, it is recommended that the special <br />adhesive UNIFIX-AEK is used for the installation of <br />SANIFIN on these substrates. In this case, modify each <br />25 kg of UNIFIX-AEK with 4.2 kg UNIFLEX-B. <br />• Follow the current valid technical data sheets for the <br />named products. <br />• Protect areas not to be treated from the effects of the <br />products used. <br />• Observe the relevant current regulations.</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>This technical data sheet does not consider local building codes or legal requirements. It shall be used as general reference for the product, based on our current knowledge <br />and experience. Legally binding is only the latest Data Sheet from one of our foreign subsidaries inside their sales territory. In any case of uncertainty please consult our <br />technical department for further information. <br />6/6</p> <p>WKD/CoS/TM 32/16</p>
