ASO-DB-Standard Technical Data Sheet EN 3217.pdf
2 စာမျက်နှာများ
548 KB
Download
<h1>ASO-DB-Standard Technical Data Sheet EN 3217.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASO®-DB-Standard</p> <p>Art.-No 2 05987</p> <p>Waterproof tape</p> <p>• water impermeable <br />• elastic <br />• UV stabilized <br />Areas of application: <br />ASO-DB-Standard is used for the formation of flexible, <br />water impermeable movement joints and connecting <br />joints beneath tiles within e.g. SANIFLEX, <br />AQUAFIN-1K-PREMIUM, AQUAFIN-2K, <br />AQUAFIN-2K/M, AQUAFIN-RS300 and ASOFLEX-AKB <br />waterproof membranes. <br />ASO-DB-Standard is easy to use and forms an intimate <br />bond with the above named waterproof systems. <br />ASO-DB-Standard can be used in wet duty classes A0 <br />and B0 in accordance with the ZDB information sheet <br />“Bonded waterproof membranes”. <br />ASO-DB-Standard fulfills the requirements of the test <br />principles of the DIBt and the information sheet “Bonded <br />waterproof membranes” that relate to the conditions in <br />wet duty classes A and C. <br />Technical Data: <br />Basis: polyester fabric with a <br />thermoplastic polyvinyl <br />chloride (PVC) elastomer <br />coating <br />Colour: grey <br />Thickness: <br />0.62 – 0.80 mm <br />Bursting pressure max: <br />approx. 4 bar <br />Impermeability to <br />water in accordance <br />with DIN EN 1928: <br />≥ 1.5 bar <br />Temperature resistance: from -22° C to +60° C <br />UV resistance: minimum 500 hours according <br />to DIN EN ISO 4892-2</p> <p>Elongation, longitudinal <br />according to DIN 527-3: ≥ 20% <br />Elongation, transverse <br />according to DIN 527-3: ≥ 80% <br />The chemical resistance after 7 days storage at +22 °C, <br />is given for the following chemicals: <br /> Hydrochloric acid 3% <br />Sulphuric acid 35% <br />Citric acid 100 g/l <br />Potassium hydroxide 3% <br />Sodium hydroxide 0.3 g/l <br />Salt water 20 g/l (sea salt) <br />Packaging: 50 m roll (up to a cutting point/15 m), <br />width 120 mm ± 2 mm, centre section <br />approx. 70 mm wide elastomer coating, <br />in a single box, 140 pieces/pallet in a <br />pallet box <br />Storage: 24 months, cool, dry, protected from <br />sunlight and weathering <br />Product application: <br />Using a 4-6 mm notched trowel, apply the waterproof <br />coating a minimum of 2 cm wider than the waterproof <br />tape, to both sides of the joint to be bridged. <br />Lay the ASO-DB-Standard into the fresh coat – <br />elastomeric strip uppermost - and subsequently carefully <br />press into the waterproof coat, without creating voids <br />or folds, using a steel trowel or roller. Watch for a full <br />bedding and coverage. The bonding must be completed <br />in such a way so that water cannot migrate around the <br />back of the ASO-DB-Standard. Over movement joints <br />lay the ASO-DB-Standard in a loop. Overlap waterproof <br />tape joints by a minimum of 5 to 10 cm, fully bond without <br />folds with the waterproof coating and then overcoat. The <br />movement joint area (for the subsequent application of an <br />elastic joint) can remain free from the waterproof coating.</p> <p>1/2</p> <p>32/17</p> <p>Advice: <br />•• Follow recognized technical regulations. <br />•• Joints that have been secured with ASO-DB-Standard <br />must be adequately protected against mechanical <br />damage. <br />•• ASO-DB-Standard may not be bonded or coated with <br />solvent-based products. <br />•• Use ASO-Joint-Tape-2000-S for wall/floor junctions in <br />areas in contact with the ground and for structural joints. <br />•• Heed the relevant current regulations. E.g. <br />DIN 18157 <br />The BEB information sheets distributed by the <br />Bundesverband Estrich und Belag e.V. <br />The ZDB information sheets, distributed by the <br />professional association of the German Tile Industry: <br />[*1] “Bonded waterproof membranes” <br />[*3] “Movement joints in tiled wall and floor finishes” <br />[*5] “Ceramic tiles, natural stone tiles and cementbound composite tiles on cement-based floor <br />constructions on insulation” <br /> [*6] “Ceramic tiles, natural stone tiles and cementbound composite tiles on heated cement-based <br />floor constructions”</p> <p>This technical data sheet does not consider local building codes or legal requirements. It shall be used as general reference for the product, based on our current knowledge and experience. <br />Legally binding is only the latest Data Sheet from one of our foreign subsidaries inside their sales territory. In any case of uncertainty please consult our technical department for further information.</p> <p>2/2</p> <p>WKD/CoS/TM</p> <p>32/17</p>
