ASO-Tape Technical Data Sheet EN 2217.pdf
2 စာမျက်နှာများ
65.6 KB
Download
<h1>ASO-Tape Technical Data Sheet EN 2217.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASO®-Tape INDUBOND-Tape-3000 </p> <p>Thermoplastic joint tape for waterproofing joints</p> <p>• Highly flexible <br />• Simple, homogenous weld <br />• No activation necessary <br />• Impermeable to water even <br />against negative pressure <br />• Can be applied to matt damp <br />substrates without priming <br />• Resistant to frost, UV and ageing</p> <p>DD-4442/ÜBB/2012</p> <p>KIWA MPA <br />Bautest GmbH</p> <p>Areas of application: <br />ASO-Tape is used in combination with ASODUR-K4031 <br />for waterproofing day/construction joints and expansion <br />joints as well as for waterproofing cracks and voids <br />in concrete construction. It is additionally suitable for <br />waterproofing transitions, penetrations or differing <br />building materials. <br />Substrate preparation: <br />The substrate must be clean and load-bearing as well <br />as free from adhesion inhibiting materials. At the time <br />of installation it may be matt damp but not wet or <br />with saturated pores. In the area to be waterproofed, <br />mechanically prepare the substrate using suitable means <br />e.g. planing, scabbling or grit blasting etc., in order to <br />ensure a good bond. When using on substrates other <br />than concrete, assess with a trial adhesion test. <br />When applying joint waterproofing as strips it is essential <br />that the concrete has waterproof qualities. Otherwise the <br />joint waterproofing must be used in combination with a <br />surface applied waterproof membrane. <br />Product application: <br />Coat the prepared substrate on both sides of the joint to <br />be bridged with ASODUR-K4031 to a width min. 1 cm <br />wider than the ASO-Tape being used. Then lay the joint <br />tape and thoroughly bed into the adhesive layer with a <br />trowel or pressure roller without voids or folds and coat</p> <p>Art.-No. 2 06427</p> <p>over the top. In so doing, ensure that the joint tape is <br />completely bedded. The adhesive or smoothing coat <br />thickness should never be less than 1 mm. Overlap butt <br />joints by a min. of 5 to 10 cm and bond or alternatively <br />hot air weld. <br />Expansion joints: <br />Expansion joints always require a 2 mm joint tape and <br />can either be laid flush or in a loop dependent on the <br />project. To accomodate expansion, leave an unbonded <br />section of tape in the expansion area. Dependent on the <br />installation and loading e.g. overhead use or negative <br />water pressure, a reinforcing or supporting construction <br />may be necessary. <br />Hot air welding: <br />The joint tapes are cut to suit the project (butt joints or <br />corner joints) and laid on a flat substrate. Butt joints are <br />to be overlapped by a min. 5 cm. The overlap area <br />is to be roughened with abrasive paper and cleaned. <br />Welding is carried out with hot air equipment with a wide <br />nozzle and a pressure roller. The welding temperature <br />(reference values: approx. 300 - 350 °C) is to be set by <br />a trial weld. The joints in the tapes are laid on top of one <br />another appropriately and fixed at the edges by selective <br />welding in order to prevent slipping during welding. Then <br />the wide nozzle of the hot air tool is drawn slowly and <br />evenly over the overlap area and fully joined together <br />with a pressure roller. Before installing check the weld for <br />a complete watertight bond. <br />Technical Data: <br />Basis: <br />TPE (Thermoplastic Elastomer) <br />Colour: grey <br />Shore A hardness <br />to ISO 868: <br />approx. 87 <br />Temperature resistance: -30°C / +90°C <br />Application, substrate <br />and material <br />temperature: <br />+ 5°C to + 35°C</p> <p>1/2</p> <p>22/17</p> <p>Material thickness</p> <p>1.0 mm</p> <p>2.0 mm</p> <p>Weight per unit <br />area, g/m²</p> <p>approx. 900</p> <p>approx. 1800</p> <p>Tensile strength <br />at break, to DIN <br />EN ISO 527-3, N/ <br />mm²</p> <p>approx. 14.0</p> <p>approx. 14.0</p> <p>Elongation at break, approx. 1000 <br />to DIN EN ISO <br />527-3, %</p> <p>approx. 1000</p> <p>Tear propogation <br />strength, to DIN <br />12310-2, N:</p> <p>approx. 200</p> <p>approx. 100</p> <p>Consumption ASODUR-K4031: <br />Consumption in kg/m <br />Size/ <br />Thickness</p> <p>1.0 mm</p> <p>2.0 mm</p> <p>150 mm</p> <p>approx. 0.8</p> <p>approx. 1.4</p> <p>200 mm</p> <p>approx. 1.0</p> <p>approx. 1.5</p> <p>250 mm</p> <p>approx. 1.1</p> <p>approx. 1.7</p> <p>300 mm</p> <p>approx. 1.3</p> <p>approx. 1.8</p> <p>500 mm</p> <p>approx. 1.8</p> <p>approx. 2.4</p> <p>Sizes: 150, 200, 250, 300, 500 <br />1000 mm <br />Storage: dry and protected from <br />weathering, 12 months in the <br />original unopened packaging. <br />Use within 2 months once <br />opened. <br />Advice: <br />• Unlike Hypalon tapes, ASO-Tape does not require <br />additional surface activation. It must not be brought <br />into contact with solvents. <br />• Protect the joint tape from mechanical damage by <br />suitable protective measures. <br />• With negative water pressure > 0.5 bar a suitable <br />supporting system (apron plate) is indispensible.</p> <p>Does not consider extra material consumption for <br />uneven substrates. <br />Combined test with ASODUR-K4031: <br />Tensile adhesion <br />strength, to PG- ÜBB: > 3.0 N/mm² with break <br />in concrete <br />Water impermeability, <br />positive and negative <br />according to DIN 1048: 5 bar <br />Crack bridging to <br />PG-ÜBB, 1.0 mm crack <br />held for 28 d water <br />pressure 0.75 bar: <br />passed <br />Reaction to fire: Class E to DIN EN 13501-1 <br />Packaging: <br />20 m rolls <br />This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>SF/CoS/TM</p> <p>22/17</p>
