INDU-Primer-S_GB_TM_1017.pdf
2 စာမျက်နှာများ
51.3 KB
Download
<h1>INDU-Primer-S_GB_TM_1017.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>INDU-Primer-S</p> <p>Technical Data Sheet <br />PRIMER-2000-S </p> <p>Primer/Adhesion promoter for porous contact areas</p> <p>• Very good adhesion to porous substrates. <br />• Very good resistance to moisture, miscellaneous <br />solvents, acids and bases. <br />Areas of application: <br />INDU-Primer-S is used as an adhesion promoting <br />primer on porous contact areas such as e.g. concrete, <br />cement-based screeds, granite pavers for the sealants <br />INDUFLEX-MS, INDUFLEX-PS and INDUFLEX-PU. <br />Technical Data: <br />Basis: <br />two component epoxy resin <br />Colour: <br />colourless, yellowish <br />Consistency: brushable <br />Density: <br />approx. 1.0 g/cm3 <br />Mixing ratio: 100 : 30 parts by weight <br />Application <br />temperature: +5° C to +30° C <br />approx. 2 to 3 hours <br />Pot life*): <br />Flash off time*): min. 30 minutes, <br />max. 6 hours <br />Cleaning: Work tools must be carefully cleaned <br />immediately after use with the <br />appropriate cleaner e.g. acetone. <br />Packaging: 500 ml <br />Component A and component B are <br />at a predetermined mixing ratio. <br />Storage: Cool and dry above +5° C, <br />18 months in the original unopened <br />packaging. Use opened packaging <br />promptly. <br />*)</p> <p>Art.-No. 2 06413</p> <p>Substrate/contact area: <br />See areas of application: <br />The surface to be treated must be: <br />• Dry, sound, load bearing and have a good key. <br />• Free from separating and adhesion inhibiting <br />substances. <br />Application: <br />Components A (resin) and B (hardener) are delivered <br />in a predetermined mixing ratio. Tip component B <br />into component A. Ensure that the hardener drains <br />completely from its container. Both components must <br />be intensively blended together. It is important to <br />also stir from the sides and the bottom to ensure that <br />the hardener is evenly dispersed. Stir until the mix <br />is homogenous (free from striations). The material <br />temperature during mixing should be +15° C. Do not <br />use the mixed material directly from the packaging. <br />Decant the material into a clean container and carefully <br />mix through once again. There must not be any film of <br />moisture as a result of dropping below the dew point <br />on the surface to be treated. <br />Method of application/Consumption: <br />Once the joint cross section has been prepared (see <br />technical data sheet for INDUFLEX-MS, INDUFLEX-PS <br />and INDUFLEX-PU), the joint edges are primed with <br />INDU-Primer-S in one operation with a priming brush. <br />Material consumption: 100 g/m2 <br />After waiting for a minimum of approx. 30 minutes*), joint <br />sealing can be carried out by extruding INDUFLEX-MS, <br />INDUFLEX-PS or INDUFLEX-PU.</p> <p>These values relate to +23° C and 50% relative humidity.</p> <p>1/2</p> <p>10/17</p> <p>Important advice: <br />• The material contains solvent. When working in <br />confined spaces ensure that there is adequate <br />ventilation and extraction. <br />• Protect areas not being treated from the effects of <br />INDU-Primer-S. <br />• Higher temperatures decrease and lower <br />temperatures increase the application and curing <br />time. Material consumption is also higher at lower <br />temperatures. <br />• The bond between the individual coats (primer/joint <br />sealant) can be heavily impeded through the <br />influence of dampness or contamination between <br />individual applications. <br />• When longer waiting times occur between <br />application of the coats, the old surface must be <br />well cleaned and thoroughly abraded, after which <br />the joint edges must be re-treated with the adhesion <br />promoter. <br />• After application of the adhesion promoter, protect it <br />from dampness for 4-6 hours. <br />• Applications that are not clearly explained in this <br />technical data sheet may only be carried out after <br />consultation with and written confirmation from the <br />Technical Services Department of SCHOMBURG. <br />Please observe a valid EU Health & Safety data sheet.</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding is only the German technical data sheet or the latest Data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>Höl/CoS/TM</p> <p>10/17</p>
