POWERPLAST-D2 TM engl_5112.pdf
2 စာမျက်နှာများ
217 KB
Download
<h1>POWERPLAST-D2 TM engl_5112.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold - Germany <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />mail export@schomburg.de <br />www.schomburg.de/en</p> <p>Technical Data Sheet</p> <p>POWERPLAST-D2</p> <p>Art.-No. 2 03828 <br />Non-slip dispersion adhesive conforming to DIN EN 12004</p> <p>Properties: <br />• Conforms to DIN EN 12004, <br />D2TE <br />• Ready to use <br />• Water resistant <br />• Non-slip <br />• High initial grab <br />• Creamy application <br />• Deformable <br />• Solvent free</p> <p>See printed batch number <br />SCHOMBURG GmbH & Co. KG <br />Aquafinstraße 2–8 <br />D-32760 Detmold</p> <p>EN 12004 <br />POWERPLAST-D2</p> <p>Improved dispersion adhesive <br />with additional characteristics</p> <p>D2 <br />Reaction to fire: class E</p> <p>Areas of application: <br />POWERPLAST-D2 is a non-slip, water resistant <br />dispersion adhesive with improved characteristics with <br />extended open time. POWERPLAST-D2 has a stress <br />neutralising function and is therefore advantageous <br />for use on lightweight partition walling and concrete <br />elements. <br />POWERPLAST-D2 is used for the thin bed installation of <br />ceramic tiles and mosaics onto flat, porous substrates <br />such as concrete, pre-cast concrete units, aerated and <br />expanded concrete, renders/plasters of groups PII to <br />PV, dry lining boards such as plasterboard, moisture <br />resistant plasterboard and gypsum fibre boards as <br />well as lightweight construction boards e.g. rigid foam <br />tilebacker panels and similar, in interior areas. <br />POWERPLAST-D2 is suitable for the installation of large <br />format tiles, also onto to existing ceramic finishes. <br />POWERPLAST-D2 can be used for tiling in moderately <br />wet duty areas such as e.g. normal domestic <br />bathrooms, onto mineral-based and dispersion-based <br />bonded SCHOMBURG waterproof membranes. <br />POWERPLAST-D2 is suitable for wall areas in wet duty <br />classification A0 in accordance with the ZDB data sheet <br />‘bonded waterproof membranes’. <br />Technical Data: <br />Basis: <br /> <br />Colour: <br />Specific gravity: <br />Substrate / <br />application temperature: <br />Temperature resistance: </p> <p>acrylic resin dispersion with <br />functional fillers and additives <br />cream white <br />1.6 kg/dm3 <br />+5° C to +30° C <br />-10° C to +70° C</p> <p>Open time *): <br />Grout after *): <br /> <br /> <br />Fully serviceable *): <br />Cleaning: <br /> <br />Certification: <br /> <br />Consumption: <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br />Adhesive bed thickness: <br />Packaging: <br />Storage: <br /> <br /> <br /> </p> <p>up to approx. 30 minutes <br />approx. 1 day, with large <br />format tiles or on impervious <br />substrates approx. 7 days <br />after approx. 14 to 21 days <br />with water immediately <br />after use <br />conforms to DIN EN 12004, <br />D2 TE, MPA Dresden <br />approx. 1.5 kg/m2 <br />per mm thickness <br />approx. 2.1 kg/m2 with a <br />4 mm notched trowel <br />approx. 3.2 kg/m2 with a <br />6 mm notched trowel <br />approx. 4.2 kg/m2 with an <br />8 mm notched trowel <br />approx. 5.2 kg/m2 with a <br />10 mm notched trowel <br />1 to 4 mm <br />20 kg plastic buckets <br />frost free, min. 6 months in <br />the original unopened <br />packaging. Use opened <br />packaging promptly.</p> <p>*) T hese values relate to +20° C and 65% relative humidity. <br />Higher temperatures and lower relative humidity reduce, lower <br />temperatures and higher relative humidity increase these given <br />times.</p> <p>Substrate preparation: <br />When installing tiles, DIN 18157, part 1 prevails <br />with regard to the substrate, substrate preparation and <br />product application. <br />The substrate must be dry, sound, clean, load bearing, <br />adequately flat and free from separating substances <br />and penetrating cracks. Remove emulsions, paint, oil, <br />laitance and loose areas. Roughen smooth concrete <br />surfaces, prime highly porous substrates with <br />ASO-Unigrund before adhesive application. <br />When tiling to dry lining boards be aware of the <br />guidelines of the board manufacturer for cladding with <br />ceramic tiles.</p> <p>Product application: <br />POWEPLAST-D2 is spread evenly onto the prepared <br />substrate and combed through with a notched trowel. <br />When choosing a notched trowel use a notch that will <br />achieve approx. 65% adhesive coverage to the back <br />of the tile. Install the tiled finish within the open time <br />of the adhesive – finger test. On existing ceramic <br />finishes, prepare old tiled finishes with a thin coat of <br />ASO-Unigrund-S using a lamb’s wool roller in a crisscross manner. At least one of the surfaces must be <br />porous e.g. render/plaster or earthenware (biscuit) tile. <br />Important advice: <br />•W <br /> hen installing tiles in floor areas with deformable <br />adhesives we recommend UNIFIX-S3, UNIFIX-S3-Fast, <br />UNIFIX-2K or UNIFIX-2K/6. <br />•W <br /> hen installing natural or synthetic stone respect the <br />specific product properties of the cladding material <br />(tendency to discolour, risk of curling) and the <br />installation recommendations of the manufacturer. We <br />recommend that a trial fix is carried out. <br />• P erimeter, bay and movement joints are to be brought <br />through and blanked off with suitable materials e.g. <br />edge strip RD-SK50. <br />• T o avoid curling effects through water absorption <br />we recommend that with serpentinite containing <br />agglomerate/synthetic and natural stone that <br />ASODUR-EK98 be used. <br />• P OWERPLAST-D2 is an adhesive that cures through <br />drying and is therefore to be protected from water <br />and frost until fully cured. <br />• P rotect areas not being treated from the effects of <br />POWERPLAST-D2. <br />•O <br /> bserve the current pertinent regulations. <br />Therefore e.g. <br />DIN 18157 <br />DIN 18352 <br />DIN 18560 <br />EN 13813 <br />DIN 18 202 <br />DIN 1055 </p> <p>The BEB information sheets distributed by the <br />“Bundesverband Estrich und Belag e.V.” <br />The technical information for the coordination of <br />cut out points for heated floor construction. <br />The ZDB information sheets distributed by the German <br />professional tile association: <br />[*1] Bonded waterproof membranes <br />[*2] Finishes on calcium sulphate screeds <br />[*3] Movement joints in tile and slab wall and floor <br />finishes. <br />[*5] Ceramic tiles and slabs, natural and concrete <br />stone/slabs on cement-based floor constructions with <br />insulation. <br />[*6] Ceramic tiles and slabs, natural and concrete <br />stone/slabs on heated cement-based floor <br />constructions. <br />Please observe a valid EU Health & <br />Safety data sheet. <br />GISCODE: D1</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. <br />Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory. <br />51/12 WKD/CoS/JD</p>
