RD-SK50 Technical Data Sheet EN 2218.pdf
1 စာမျက်နှာ
65.6 KB
Download
<h1>RD-SK50 Technical Data Sheet EN 2218.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>RD-SK50 </p> <p>Art.-No. 2 05978</p> <p>Self adhesive edge insulation strip</p> <p>Substrate preparation: <br />All usual substrates, which are suitable for applying <br />levelling compounds and floor finishes and which have <br />been professionally prepared. Prepare the substrate <br />beforehand with a primer suitable for the intended system <br />build-up. Allow the primer to dry.</p> <p>• PE edge insulation strip <br />• Self-adhesive foot with upright effect <br />• Prevents sound bridges <br />• Prevents mortar bridges <br />• Especially suitable for renovation work <br />Areas of application: <br />RD-SK50 is used to eliminate sound and mortar bridges. <br />RD-SK50 can be used in combination with levelling <br />compounds, screeds and de-coupling systems e.g. <br />SOLOPLAN-30-PLUS, ASO-NM15, SOLOPLAN-FA, <br />SOLOCRET-15, SOLOCRET-50, the ASO-EZ product <br />range and de-coupling systems such as STEPBOARD. <br />RD-SK50 is equipped with a self-adhesive foot so that the <br />edge insulation strip can be well positioned against rising <br />building sections without leaving adhesive residues behind <br />on the wall. Therefore mortar and sound bridges are <br />eliminated. Suitable for the installation of tiles, parquet and <br />laminate especially in the renovation of apartment blocks.</p> <p>Product application: <br />1. R emove the protective film from the adhesive strip of the <br />SK foot. <br />2. S <br /> tick the RD-SK50 with the SK foot to the prepared <br />substrate and push into place with pressure. Cut <br />through the SK foot when forming corners. Once fixed, <br />the RD-SK50 presses against the wall thus eliminating <br />sound bridges and mortar bonds. <br />3. A <br /> t junctions the RD-SK50 is butt jointed without a gap. <br />Stick adhesive tape over the junctions, butt joints or cut <br />areas. <br />4. S <br /> ubsequently further work, such as e.g. levelling with <br />SOLOPLAN-30-PLUS, can be carried out.</p> <p>Technical Data: <br />Basis: PE foam with self-adhesive foot and <br />fleece backing <br />Packaging: <br />5 rolls of 20 m in a box <br />Colour: <br />grey with SCHOMBURG printed <br />Thickness/height/ <br />length: <br />5 mm/50 mm/20 m <br />Application/substrate <br />temperature: <br />+5° C to +30° C <br />Reaction to fire <br />to DIN 4102: <br />B2 <br />Storage: dry, 12 months in the original <br />unopened packaging</p> <p>Advice: <br />• Observe the Technical Data Sheets of all named <br />products. <br />• RD-SK50 may not be bonded or overcoated with <br />solvented products. <br />• The ability of the SK foot to cope with loads is <br />limited. Therefore with high vehicular traffic or bonded <br />constructions we recommend that its suitability for the <br />type of application is checked. <br />• Follow current relevant regulations such as e.g.: <br />DIN 18157 <br />DIN 18352 <br />DIN 18560 <br />EN 13813 <br />DIN 1055</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>1/1</p> <p>WKD/CoS/TM</p> <p>22/18</p>
