THERMOPAL-SR24 TM_GB_3416.pdf
2 စာမျက်နှာများ
98.2 KB
Download
<h1>THERMOPAL-SR24 TM_GB_3416.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-333 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>THERMOPAL®-SR24 <br />Mineral-based restoration plaster – WTA</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />13 <br />2 01411 <br />DIN EN 998-1-2010-12 <br />THERMOPAL-SR24 <br />Restoration Plaster (R) <br />Compressive strength <br />CS II <br />Capillary water absorption 24h, prism ≥ 0.3 kg/m2 <br />Water penetration <br />≤ 5 mm <br />Water vapor permeability <br />coefficient (μ) <br />≤ 15 <br />Tensile strength 28 d <br />≥ 0.08 N/mm2 <br />Fracture appearance <br />B <br />Thermal conductivity, λ10, dry, <br />Tabulated average value (P = 50 %), <br />DIN EN 1745 <br />< 0.47 <br />Reaction to fire <br />A1 <br />Durability <br />(Frost resistance) <br />Resistant in case of handling <br /> according to the technical data sheet</p> <p>• <br />• <br />• <br />• <br />• <br />• <br />• <br />•</p> <p>Mineral-based pre-blended mortar. <br />High volume of entrained air. <br />Vapour permeable. <br />High salt storage capacity. <br />Low consumption per surface area. <br />Ready for rubbing down at an early stage. <br />Hand or mechanical application. <br />For interior and exterior use.</p> <p>Areas of application: <br />For producing vapour permeable and dry plasters on <br />to damp and/or salt laden walls in interior and exterior <br />installations. Due to the special system properties, <br />possible mould contamination is prevented. <br />Technical Data: <br />Basis: <br />pre-blended dry mortar <br />Colour: grey <br />Water demand: <br />approx. 6 - 6.5 litres per bag <br />Bulk density: <br />1.0 - 1.1 kg/dm3 <br />Consumption: <br />approx. 9.5 kg/m2 per cm <br /> thickness <br />Thickness: <br />see table (page 2) <br />Packaging: <br />25 kg bags <br />Substrate/ <br />application temp: <br />+5° C to +30° C <br />Storage: <br />dry, 12 months in the original <br /> <br />unopened packaging. Use <br /> opened packaging promptly.</p> <p>Art.-No. 2 01411</p> <p>Substrate preparation: <br />The substrate must be load bearing and free from <br />adhesion inhibiting media such as release agents, dust <br />or other coatings. Remove old render/plaster, paint and <br />laitance up to 80 cm away from the damaged area <br />determined visibly or by analysis. <br />Rake out brittle masonry joints to a depth of 2 cm <br />and clean mechanically. Concrete surfaces must <br />be open-pored. Where the salt content is high, pretreat with ESCO-FLUAT. Apply a splatterdash coat of <br />THERMOPAL-SP as a bonding coat (degree of <br />coverage approx. 50%). <br />As an alternative to THERMOPAL-SP, the splatterdash <br />coat can be produced as follows: <br />Emulsion comprising ASOPLAST-MZ : Water, mixed 1:1 <br />to 1:3. Dry blend comprising cement and washed sand <br />– grain size 0.4 mm - mixed at a ratio 1:2 by volume. <br />Produce a workable consistency from the emulsion and <br />dry blend and use within approx. 1.5 hours. <br />Product preparation: <br />THERMOPAL-SR24 can be prepared in all usual <br />continuous mixing pumps (e.g. with the High-Pump Basic <br />from HTG-HIGH TECH Germany GmbH, Berlin or PFTG4). If, due to machinery equipment, an air entrainment <br />of 20-30% is achieved then there is no need for a <br />secondary mixer. Small quantities can be mixed by <br />hand with a drill mixer. <br />Machinery PFT-G4: <br />Pipe length: <br />Pipe size: <br />Stator / rotor: <br />Spray head for <br />scratch coat: <br />Water addition: </p> <p>max. 20 m <br />25 – 35 mm <br />D4-2 LP <br />Nozzle size > 17 mm <br />approx. 300 – 325 l/h</p> <p>THERMOPAL-SR24 can be applied with appropriate <br />tools such as plasterer‘s float, steel float or similar at <br />thicknesses in accordance with WTA guidelines as well <br />as in single layers up to 3 cm in one operation. After <br />an adequate waiting time the surface can be rubbed <br />off or finished with a felt board. Rubbing off too early <br />produces a binder concentration at the surface and may <br />cause stress cracks.</p> <p>1/2</p> <p>34/16</p> <p>As an alternative the surface can be worked with a grid <br />float. This operation can be carried out after 8 – 24 <br />hours dependent on the ambient conditions. Rubbing <br />with the grid float removes the laitance layer which <br />appears and results in a considerably greater diffusion <br />performance. Dependent on the ambient conditions the <br />surface can be smoothened with THERMOPAL-FS33. <br />For thicker coats, apply in several layers. In these cases <br />strike off the previous coat with a plasterer’s darby and <br />immediately the mortar stiffens, roughen up horizontally <br />and allow to dry. <br />Keep to a waiting time of 1 mm per day.</p> <p>• P rotect from strong sunlight. <br />• Smooth surfaces can be achieved by trowelling with <br />THERMOPAL-FS33. <br />• For coloured finishes use highly vapour permeable <br />silicate paint. <br />• Observe the WTA information sheet “Restoration <br />plaster systems” when planning and implementing <br />restoration work. <br />Please observe a current EU safety data sheet. <br />GISCODE: ZP1</p> <p>Advice: <br />• P rotect areas not to be treated from the effects of <br />THERMOPAL-SR24. <br />•V <br /> ery damp substrates may cause a lengthening of the <br />waiting time before surfaces can be roughened.</p> <p>Measures taken dependent on the degree of salting in accordance with WTA <br />Degree of salting 1)</p> <p>Measures taken</p> <p>low</p> <p>1. Splatterdash coat <br />2. THERMOPAL-SR24</p> <p>≤ 0.5 <br />≥ 2.0</p> <p>medium to high</p> <p>1. Splatterdash coat <br />2. THERMOPAL-SR24 <br />3. THERMOPAL-SR24</p> <p>≤ 0.5 <br />1.0–2.0 <br />1.0–2.0</p> <p>1. Splatterdash coat <br />2. THERMOPAL-GP11 <br />3. THERMOPAL-SR24</p> <p>≤ 0.5 <br />≥ 1.0 <br />≥ 1.5</p> <p>1)</p> <p>Thickness (cm)</p> <p>Notes <br />As a rule the splattedash dash <br />coat does not completely cover <br />Total thickness: <br />Min. 2.5 cm, max. 4 cm <br />roughen up previous coat <br />as necessary <br />Drying time of individual <br />coats: 1mm/day</p> <p>To be determined and calculated by preliminary testing.</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. <br />Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>SF/CoS/TM</p> <p>34/16</p>
