UNIFIX-S3-fast NEW Technical Data Sheet EN 1318.pdf
4 စာမျက်နှာများ
633 KB
Download
<h1>UNIFIX-S3-fast NEW Technical Data Sheet EN 1318.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>UNIFIX®-S3-fast </p> <p>Art. no. 2 04310</p> <p>X-S3-f <br />IFI <br />a</p> <p>C2</p> <p>FT <br />E</p> <p>S2</p> <p>N</p> <p>st</p> <p>U</p> <p>Highly-flexible rapid adhesive mortar for tiles</p> <p>EN</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstraße 2–8 <br />D-32760 Detmold</p> <p>1200</p> <p>4</p> <p>18</p> <p>2 04310 <br />EN 12004</p> <p>UNIFIX-S3-fast <br />Rapid-hardening, cement-based mortar for increased demands <br />in interior and exterior areas for tiling and board-laying work</p> <p>C2 F <br />Reaction to fire: </p> <p>TILE</p> <p>Class E</p> <p>Bonding strength as <br />tensile adhesion strength after dry storage: </p> <p>≥ 1 N/mm²</p> <p>Durability as <br />tensile adhesion strength after water storage: </p> <p>≥ 1 N/mm²</p> <p>Tensile adhesion strength after warm storage: ≥ 1 N/mm² <br />Tensile adhesion strength after alternating <br />frost/thaw storage: </p> <p>≥ 1 N/mm²</p> <p>Early tensile adhesion strength, after 6 hours: ≥ 0.5 N/mm²</p> <p>• Highly-flexible special tile adhesive <br />• For critical substrates and high stresses <br />• Can also be used on new substrates <br />• Waterproof and frost-resistant <br />• Vapour permeable <br />• For interior and exterior areas <br />• Rapid-setting <br />• Rapid crystalline binding of the mixing water <br />• Creamy white <br />• In accordance with DIN EN 12004, C2 FTE S2 <br />Areas of use: <br />UNIFIX-S3-fast is used as a thin-bed mortar, particularly <br />for laying vitrified tiles with low water absorption ≤ 0.5 % <br />(porcelain stoneware), stoneware, clinker, and mosaic <br />on new cement-based substrates. Thanks to the high <br />deformability of UNIFIX-S3-fast, damaging shear stresses <br />in the covering can be largely compensated out and so <br />it is also particularly well suited to use as bedding mortar <br />for large formats. UNIFIX-S3-fast is primarily used on floor <br />areas. <br />UNIFIX-S3-fast is particularly well suited to use on <br />balconies and terraces, in swimming pool surrounds,</p> <p>on heated constructions, on new, load-bearing, cementbased substrates and for laying tiles and boards with low <br />water absorption. <br />Thanks to the high elasticity, high stresses, such as occur <br />between substrates and coatings in exterior areas or <br />when laying on new, walkable cement-based screeds <br />(approx. 3 days after being put down) and heated <br />screeds, for example, can also be reliably absorbed <br />with UNIFIX-S3-fast. <br />The vapour permeability of UNIFIX-S3-fast guarantee <br />that cement-based substrates that are still moist will dry <br />out properly, even when laying is carried out early. The <br />obligatory heating of the screed before laying ceramic <br />materials can be omitted. <br />As a result of the rapid crystalline binding of the mixing <br />water, the flexible mortar is suitable for a variety of <br />artificial and natural stone. When laying natural stone <br />materials, the product-specific properties of the natural <br />stone, e.g. sensitivity to discolouration and curling effects, <br />must be taken into account. We recommend <br />ASODUR-EK98 or ASODUR-DESIGN for laying stone <br />that contains serpentinite. <br />UNIFIX-S3-fast is a system component on mineral and <br />dispersion-bound SCHOMBURG bonded waterproof <br />systems in the wear classes A, A0, B0 and water influence <br />classes W0-I, W1-I, W2-I, W3-I. <br />Technical data: <br />Combination product comprising: <br /> <br />A component <br /> <br />Powder <br /> <br />component <br />Basis: <br />Aggregate <br /> <br />special binding <br /> <br />agent based <br /> <br />on cement, <br /> <br />additives </p> <p>1/4</p> <p>B component <br />Liquid <br />component <br />liquid polymer</p> <p>13/18</p> <p>Colour: <br />Creamy white <br />White <br />Mixing <br />ratio: <br />3 parts by weight 1 part by weight <br />Packaging: <br />15 kg sack <br />5 kg canister <br />Storage: Dry, 12 months <br />frost-free, 12 months <br />in the original unopened container <br />UNIFIX-S3-fast (combination product) <br />Mixing ratio: <br />15 kg A-comp. (powder): 5 kg B-comp. : up to 1.35 l <br />water, depending on desired slump resistance <br />Application/ <br />substrate temp.: <br />+5 °C to +25 °C <br />Pot life*): <br />approx. 45 minutes <br />Adhesive open <br />time*): <br />up to approx. 30 minutes <br />Thin-bed mortar: up to approx. 5 mm layer thickness <br />Ready for grouting*): after approx. 6 hours <br />Foot traffic after*): after approx. 6 hours <br />Fully cured*): After minimum 7 days, depending <br />on the absorbency properties of the <br />substrate <br />Cleaning: Clean immediately after use with <br />water <br />Deformability: <br />> 5 mm per DIN 12004 <br />Testing: In accordance with EN 12004 <br />test report 1200/897/17a MPA <br />Braunschweig <br />Consumption: approx. 2.9 kg/m2 with 6 mm <br />notched trowel <br />approx. 3.8 kg/m2 with 8 mm <br />notched trowel <br />approx. 4.8 kg/m2 with 10 mm <br />notched trowel <br />*) The values apply for +23 °C and 50 % relative humidity; higher temperatures <br />shorten, lower temperatures extend the time cited.</p> <p>Substrate: <br />The substrate must be dry, load-bearing, adequately <br />level, free of penetrating cracks and free of separating <br />substances, such as oils, paints, laitance layers and</p> <p>loose particles. It must have a primarily closed surface <br />condition and exhibit strength typical of its type. Substrate <br />preparation and application per DIN 18157, part 1, and <br />the application specifications of UNIFIX-S3-fast that differ <br />from this, are authoritative when laying tiles. <br />Prime absorbent substrates with ASO-Unigrund. Calcium <br />sulphate screeds must be roughened, vacuumed and <br />primed with ASO-Unigrund - as with all calcium sulphate <br />bound substrates. Heated screeds must be heated in <br />accordance with recognised standards before installation <br />of coverings. Moisture measurement should be carried <br />out with the CM device to assess whether it is ready for <br />laying on. The CM moisture readings may not exceed <br />• CA without floor heating system ≤ 0.5% <br />• CA with floor heating system ≤ 0.3%. <br />Tiles can be laid on cement-based screeds with <br />UNIFIX-S3-fast, as soon as the screed is able to withstand <br />loads. Concrete substrates after 28 days. The CM <br />measurement must be completed in accordance with the <br />current working instructions FBH-AD from the technical <br />information "Interface coordination with heated floor <br />constructions". Surface irregularities in substrates that are <br />ready for laying can be compensated out beforehand <br />with SOLOPLAN-30-PLUS, for example. <br />Application: <br />UNIFIX-S3-fast is a combination product and is shipped <br />in accordance with the mixing ratio. First, add the B <br />component into a clean mixing bucket. Next, add <br />the A component (powder) and continue mixing until <br />a homogeneous bulk density is produced. For lighter <br />working up to 1.35 l of water can be added, depending <br />on the desired slump resistance. After a short maturing <br />time, mix again. Do not mix more UNIFIX-S3-fast than can <br />be used within the pot life. <br />Mixing ratio: <br />15 kg A component (powder): 5 kg B component : <br />depending on the desired consistency, spread up to</p> <p>2/4</p> <p>13/18</p> <p>1.35 l water UNIFIX-S3-fast evenly onto the substrate and <br />comb through with an suitable notched trowel, depending <br />on the board size/material. Lay the surfacing materials <br />within the adhesive open time (finger test). In exterior <br />areas and continuously wet areas, ensure that there <br />are no cavities in the bedding for the tiles and boards. <br />Special notched trowels (e.g. HFV notch, Flowline) have <br />proven useful for this. <br />Notes: <br />•W <br /> hen laying natural stone and synthetic stone, the <br />product-specific properties of the coating materials <br />(tendency for discolouration, curling effects, etc.) and <br />the laying recommendations of the manufacturer must <br />be taken into account. We recommend carrying out <br />a trial laying. <br />• T he relevant guidelines (DIN, ZDB data sheets <br />[German construction industry association]) still insist <br />on a 28-day waiting time for cement-based substrates. <br />Our experience with the elastic thin-bed mortar <br />UNIFIX-S3-fast have shown that damage-free laying is <br />certainly possible on newer substrates. For this reason, <br />we recommend agreeing this special construction <br />method in the contract. <br />•W <br /> ith the combination of newer substrates and the <br />laying of large-format tiles, the tile size should be <br />restricted to max. 60 × 60 cm. A joint width of min. <br />3 mm should be planned. With formats larger than <br />60 × 60 cm, the CM moisture of the screed should also <br />be checked. For cement-based screeds on insulation or <br />separating layers, in this case a CM moisture readings <br />of ≤ 2.0 CM % should be complied with. <br />• P rerequisite for laying tiles on new substrates is <br />compliance with the following criteria: The arrangement <br />of movement joints complies with the relevant guidelines. <br />Use notched trowel of min. 10 mm in order to be able to <br />accommodate minor deformations of the substrate. <br />Heating screed constructions must generally be <br />completed from the 21st day after laying the screed <br />in accordance with the relevant guidelines (ZDB data</p> <p>sheet). The earliest possible time for starting laying is <br />after the screed is walkable, generally after minimum <br />3 to 8 days. The screed must have reached minimum <br />70% of its final strength (in normal cases, after 7 days). <br />Complete grouting with hydraulically hardening grout, <br />e.g. ASO-Flexfuge or HF05-Brillantfuge. <br />• When working on new, cement-based substrates <br />(screed, heated screed), the reduced full service <br />conditions of the screed construction must be taken into <br />account. Do not place heavy tools, surfacing materials, <br />etc., on the screed, in particular in areas at risk of <br />breakage – ensure load spreading measures. <br />• To avoid curling effects due to water absorption, we <br />recommend using ASODUR-EK98 when working with <br />agglomerates / synthetic stone. <br />• Direct solar radiation and draughts can result in <br />a skin forming prematurely or to the open time being <br />shortened. <br />• UNIFIX-S3-fast is a hydraulically hardening mortar with <br />a dispersion component rate that can take several days <br />before being fully hardened in unfavourable climatic <br />conditions or when exposed to weather influences and <br />so it must be protected from exposure to water and <br />frost in the meantime. <br />• Protect surfaces that are not to be treated from the <br />effects of UNIFIX-S3-fast. <br />• Avoid contact with eyes and skin. <br />• Prime calcium sulphate bound substrates with <br />ASO-Unigrund-GE or ASO-Unigrund-K (mix ratio 1:3 <br />with water)! When laying tiles on calcium sulphate <br />bound substrates, UNIFIX-AEK is useful to avoid <br />ettringite formation with residual moistures of 1.0 % with <br />heated or 1.5 % per CM with unheated constructions! <br />• Do not add water or new mortar to existing thin-bed <br />mortar already in the binding process in order to <br />make it workable again as this would involve a risk of <br />inadequate strength development! <br />• Direct contact between cement tile mortar and <br />magnesite screeds leads to the destruction of the <br />magnesite screeds through a chemical reaction known <br />as "magnesite pouring". Moisture pressure from</p> <p>3/4</p> <p>13/18</p> <p>the rear of the substrate must be prevented through <br />appropriate measures. The magnesite substrate should <br />be mechanically roughened and primed with the epoxy <br />resin ASODUR-V360W plus max. 5 % water (approx. <br />250 g/m2). After a waiting time of approx. 12–24 <br />hours at +20 °C, the second coat of <br />ASODUR-V360W should be applied (approx. <br />300–350 g/m2). While the second coat is still fresh, <br />apply plenty of quartz sand with 0.5–1.0 mm grain <br />size. Installation of coverings may be completed after a <br />further waiting time of approx.12-16 hours. <br />• The current relevant regulations are to be observed! <br />So, for example: <br />DIN 18157 <br />DIN 18352 <br />DIN 18560 <br />DIN 18202 <br />EN 13813 <br />DIN 1055 <br />The BEB data sheets, issued by the Bundesverband <br />Estrich und Belag e.V. [Federal association for screed <br />and covering]. <br />The technical information "Interface coordination with <br />heated floor constructions” <br />The ZDB data sheets, issued by the Fachverband des <br />deutschen Fliesengewerbes [professional association <br />of the German tile trade]: <br /> [*1] "Bonded waterproof systems" <br /> [*2] "Coatings on calcium sulphate screed" <br /> [*3] "Movement joints in cladding and coverings <br />made of tile and boards" <br /> [*5] "Ceramic tiles and boards, natural stone <br />and synthetic stone on cement-based floor <br />constructions with insulation layers" <br /> [*6] "Ceramic tiles and boards, natural stone and <br />synthetic stone on heated, cement-based floor <br />constructions” <br /> [*7] "Exterior coverings" <br /> [*8] "Coverings on mastic asphalt screed" <br /> [*9] "Height differences"</p> <p> [*10] "Tolerances" <br /> [*11] "Cleaning, protecting, maintenance" <br /> [*12] "Swimming pool construction" <br />Please observe valid EU safety data sheets! <br />GIS CODE: A-comp. ZP1 <br /> <br />B-comp. D1</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the <br />case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not <br />release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />4/4</p> <p>WKD/TAN/TM</p> <p>13/18</p>
